• de
  • en
  • fr
  • International Database for Civil and Structural Engineering

RESTON®STU – Shock Transmission Units

The mageba Shock Transmission Unit (STU) is designed to be connected between bridge structure components to form a rigid link under dynamic loads induced by forces such as vehicle braking and earthquakes. It can be used for strengthening of simple and continuous span bridges by distributing the acting horizontal loads (e.g. breaking forces) among all piers and abutments.

Product Summary

The mageba Shock Transmission Unit (STU) is designed to be connected between bridge structure components to form a rigid link under dynamic loads induced by forces such as vehicle braking and earthquakes. At the same time, the structure will be able to move freely under slowly applied loads such as temperature, creep and shrinkage.

The unit is connected between elements of bridge structures at expansion joints, or near the bearings between the super-structure and the substructure. The use of STUs allows the load sharing of a suddenly applied force.

Design Principle

Shock Transmission Units work on the principle that rapid passage of a viscous fluid through a narrow gap, orifice or port generates high resistance, while slow passage at low velocity generates only minor resistance. An STU should block the deck of a bridge during a quick motion and behave like a spring with a very high stiffness. At the same time, the STU should deliver a low reaction force during the slow displacements of e.g. thermal expansion contraction of the deck.

The mageba STU is made with a steel reservoir, with a piston rod sliding through it. On the piston rod, there is a fixed head, which in effect separates the reservoir into two chambers. When the unit is filled with silicone fluid, the pressure is the same in both chambers.

Anchoring System

mageba Shock Transmission Unit (STU) can be delivered with the entire anchoring system. Depending on the bridge type, steel or concrete connections are required. The fixing from the STU to the connection base plate is made with bolts making the STU easily exchangeable.

The rotational capacity between the STU and the support construction is guaranteed by the use of a high quality spherical plain bearing.

Common Applications

The mageba STU can be used for a wide range of applications. Following examples are most common applications:
  • Strengthening simple and continuous span bridges by distributing the acting horizontal loads (e.g. breaking forces) among all piers and abutments
  • Connecting the pier of a cable stayed bridge with its deck, allowing free movements during normal operations and a rigid connection during seismic activities
  • Retrofitting existing bridges at minimal costs where seismic up-grades are required

Materials

Following materials are used for the production of mageba STUs:
  • Main outer steel parts such as cylinder tubes, cylinder pipe, etc. made out of steel S355 according to DIN EN 10025-2
  • Piston rod made out of steel 42CrMo4 according to DIN EN 10083-1
  • Hydraulic valves made out of cast steel according to ISO 3755

Corrosion Protection

Corrosion protection according to DIN EN ISO 12944, C4ANV695, expected durability L (long). Target of surface roughness: Rz min 60µm, or alternatively Elcometer-roughness 2. Applied layers: Sand blasting Sa 2 ½, Zinc dust 2K-EP-primer 2-pack 50µm, MIO EP 2-pack 2x70µm, MIO-PUR, 2-pack 40µm. Total target thickness 230µm, Quality level 100% parts conform.

Sealing

The sealing represents the most critical element of the total hydraulic system. Therefore, mageba employs a high grade sealing that demonstrates a quasi zero natural wear and an absolute physical-chemic compatibility with the adopted viscous fluid.

Viscous Fluid

The mageba viscous fluid is based on a silicon oil with special additives, protecting it against natural aging and the STUs from inner corrosion. With respect to temperature variations, the viscosity of this selected fluid shows a nearly constant characteristic. This characteristic facilitates the mechanical system to be thermically compensated.

Temperature and Aging

A variation of the outside temperature, which can range from -55°C to + 80°C, does not change the amount of energy dissipated per cycle. There is no aging of the silicone fluid. The mageba units have been tested in very severe environmental conditions, including fire.

Testing

Full-scale testing can be carried out, if required. mageba performs its tests at a recognised independent test institute. Commonly used tests are:
  • Damping efficiency test to evaluate the energy dissipating capability
  • Constitutive law test to determine the damper’s characteristic curve force vs. velocity
  • Impressed low velocity test to evaluate the damper’s axial force resistance under simulated thermal movements

Monitoring System

An optional monitoring system is available and includes measuring units such as oil temperature gauge, distance control systems, oil pressure sensors, and so forth. The output is realised through an analogue output 4-20mA or 0-10V.

Where an STU can be applied

STUs can be used for both steel and concrete structures. STUs can be used on cable stayed and suspension bridges to eliminate large displacements of the deck during an earthquake. For other civil engineering structures such as buildings, STUs can provide additional rigidity in the frame structure. STUS can also be used to strengthen adjacent buildings during a seismic event. The retrofit of existing steel truss railway bridges with STUs can allow heavier trains (increased weight per axle) and take the increased braking forces without a change to the substructure. STUs can be made to strengthen supporting piers, which have been found inadequate due to increase in traction and braking forces, or which have sustained damage caused by corrosion.

Inspection & Maintenance

Thanks to the use of high quality components, the application of advanced design methods and a functioning quality assurance system, mageba’s STU can be regarded as maintenance free. Nevertheless, mageba recommends an inspection to be carried out at least every 3 years. Upon delivery of the STUs, mageba submits to the engineer an inspection and maintenance manual, allowing a regular and appropriate inspection to be carried out by the operations and maintenance staff.

Inquiry for further information

Fields marked with a red asterisk * must be completed for the message to be sent.

Services
Offered by

References

Rougemont, Vaud, Switzerland (1905)

Gstaad, Saanen, Berne, Switzerland (1905)

Cádiz, Cádiz, Andalusia, Spain (2015)

Tarrytown, Westchester County, New York, USA, North America - Nyack, Rockland County, New York, USA (2018)

Similar Products & Services

  • About this
    data sheet
  • Product-ID
    45
  • Date created
    10/01/2011
  • Last Update
    16/02/2017