Yamei Zhang 
- (2025): Load-bearing characteristics and optimization design for rock-socketed bored piles in sandy silty clay in coastal areas. In: Soil Dynamics and Earthquake Engineering, v. 190 (March 2025).
- (2024): Influence of waste glass powder on printability and mechanical properties of 3D printing geopolymer concrete. In: Developments in the Built Environment, v. 20 (December 2024).
- (2024): The positive role of phosphogypsum in dredged sediment solidified with alkali-activated slag. In: Construction and Building Materials, v. 442 (September 2024).
- (2024): Optimization strategy for incorporating recycled brick powder in 3D-printed concrete by balancing low carbon footprint and enhanced performance. In: Construction and Building Materials, v. 443 (September 2024).
- (2024): An investigation on enhancing the bonding properties of 3D printed concrete permanent formwork and post-casted concrete. In: Construction and Building Materials, v. 444 (September 2024).
- (2024): Silane treatment for sisal fibers to improve the degradation resistance and interface with cement matrix. In: Construction and Building Materials, v. 429 (May 2024).
- (2024): Printability and mechanical properties of 3D printing ultra-high performance concrete incorporating limestone powder. In: Construction and Building Materials, v. 426 (May 2024).
- (2024): Uncovering the influence of red mud on foam stability and pore features in hybrid alkali-activated foamed concrete. In: Construction and Building Materials, v. 416 (February 2024).
- (2023): Revealing the difference between creep behavior of hydration products of Portland cement and alkali-activated slag paste at early age. In: Journal of Building Engineering, v. 77 (October 2023).
- (2023): Investigation of the rheological and mechanical properties of 3D printed eco-friendly concrete with steel slag. In: Journal of Building Engineering, v. 72 (August 2023).
- (2019): The microstructural change of C-S-H at elevated temperature in Portland cement/GGBFS blended system. In: Cement and Concrete Research, v. 123 (September 2019).
- (2022): Numerical Simulation of Bearing Characteristics of Bored Piles in Mudstone Based on Zoning Assignment of Soil around Piles. In: Buildings, v. 12, n. 11 (27 October 2022).
- (2023): Study on damage constitutive relationship of mudstone affected by dynamic pile driving. In: Soil Dynamics and Earthquake Engineering, v. 164 (January 2023).
- (2023): Research of jacked pile penetration test based on airbag loading. In: Soil Dynamics and Earthquake Engineering, v. 164 (January 2023).
- (2022): Study of the influence of sand on rheological properties, bubble features and buildability of fresh foamed concrete for 3D printing. In: Construction and Building Materials, v. 356 (November 2022).
- (2022): Pore structure, internal relative humidity, and fiber orientation of 3D printed concrete with polypropylene fiber and their relation with shrinkage. In: Journal of Building Engineering, v. 61 (December 2022).
- (2022): A two-phase design strategy based on the composite of mortar and coarse aggregate for 3D printable concrete with coarse aggregate. In: Journal of Building Engineering, v. 54 (August 2022).
- (2021): Properties of dredged sludge solidified with alkali-activated slag-based materials and blended with copper slag as fine aggregates of mortars. In: Construction and Building Materials, v. 312 (December 2021).
- (2022): Synergistic effect of polycarboxylate superplasticizer and silica fume on early properties of early high strength grouting material for semi-flexible pavement. In: Construction and Building Materials, v. 319 (February 2022).
- (2021): Surface etching and early age hydration mechanisms of steel slag powder with formic acid. In: Construction and Building Materials, v. 280 (April 2021).
- (2022): Optimization of 3D printing concrete with coarse aggregate via proper mix design and printing process. In: Journal of Building Engineering, v. 56 (September 2022).
- (2022): Mechanical anisotropy evolution of 3D-printed alkali-activated materials with different GGBFS/FA combinations. In: Journal of Building Engineering, v. 50 (June 2022).
- (2021): Morphological and mineralogical insights into acetic acid modifying and hydraulic process on steel slag for enhanced reactivity. In: Construction and Building Materials, v. 307 (November 2021).
- (2020): Rheology, shrinkage and pore structure of alkali-activated slag-fly ash mortar incorporating copper slag as fine aggregate. In: Construction and Building Materials, v. 242 (May 2020).
- (2018): Ultrasonic monitoring of setting and hardening of slag blended cement under different curing temperatures by using embedded piezoelectric transducers. In: Construction and Building Materials, v. 159 (January 2018).
- (2019): Ultrasonic Monitoring of Crack Propagation of Notched Concretes Using Embedded Piezo-electric Transducers. In: Journal of Advanced Concrete Technology, v. 17, n. 8 (August 2019).
- (2019): Products and properties of steam cured cement mortar containing lithium slag under partial immersion in sulfate solution. In: Construction and Building Materials, v. 220 (September 2019).
- (2011): Investigation into the Fatigue Damage Process of Rubberized Concrete and Plain Concrete by AE Analysis. In: Journal of Materials in Civil Engineering (ASCE), v. 23, n. 7 (July 2011).
- (2016): Statistical nanoindentation technique in application to hardened cement pastes: Influences of material microstructure and analysis method. In: Construction and Building Materials, v. 113 (June 2016).
- (2018): Properties of alkali-activated ground granulated blast furnace slag blended with ferronickel slag. In: Construction and Building Materials, v. 192 (December 2018).
Structurae cooperates with
