Peng Xu 
- (2024): A general and simple method to disperse 2D nanomaterials for promoting cement hydration. In: Construction and Building Materials, v. 427 (May 2024).
- (2024): Performance Optimization and Numerical Simulation Study of Sludge Low-Temperature Drying System. In: Journal of Environmental Engineering (ASCE), v. 150, n. 5 (May 2024).
- (2023): A novel approach for chloride control in sea sand cement composites utilizing graphene oxide. In: Construction and Building Materials, v. 389 (July 2023).
- (2023): Multi-Zone Infection Risk Assessment Model of Airborne Virus Transmission on a Cruise Ship Using CONTAM. In: Buildings, v. 13, n. 9 (23 August 2023).
- (2023): A Fast Method for Calculating the Impact of Occupancy on Commercial Building Energy Consumption. In: Buildings, v. 13, n. 2 (14 February 2023).
- (2023): Influence of reinforcement design on seismic stability of full-height panel MSE walls. In: Soil Dynamics and Earthquake Engineering, v. 165 (February 2023).
- (2022): Investigation into bearing performance of concrete expanded-plates piles: Field test and numerical modelling. In: Engineering Structures, v. 271 (November 2022).
- (2015): Model Based Indirect Submetering Method of HVAC End-use in Existing Office Building. In: Procedia Engineering, v. 121 ( 2015).
- (2021): Microscopic performance of modified asphalt based on aging. In: Construction and Building Materials, v. 279 (April 2021).
- (2014): Numerical Studies on Smoke Spread in Urban Underground Tunnel with Horizontal Junctions. In: Procedia Engineering, v. 71 ( 2014).
- (2020): Limit analysis of bearing capacity and failure geometry of GRS bridge abutments. In: Computers and Geotechnics, v. 127 (November 2020).
- (2022): Nonlinear eccentric bending and buckling of laminated cantilever beams actuated by embedded pre-stretched SMA wires. In: Composite Structures, v. 284 (March 2022).
- (2022): An interpretable method for identifying mislabeled commercial building based on temporal feature extraction and ensemble classifier. In: Sustainable Cities and Society, v. 78 (March 2022).
- (2022): Identification of Creep Camber State of 32-m Box Girders on High-Speed Railway and Prediction of Geometry of Track over Girder. In: Journal of Transportation Engineering, Part A: Systems, v. 148, n. 3 (March 2022).
- (2016): Optimal Match Method for Milepoint Postprocessing of Track Condition Data from Subway Track Geometry Cars. In: Journal of Transportation Engineering, v. 142, n. 8 (August 2016).
- (2021): A non-intrusive approach for fault detection and diagnosis of water distribution systems based on image sensors, audio sensors and an inspection robot. In: Energy and Buildings, v. 243 (July 2021).
- (2017): A new local pressure loss coefficient model of a duct tee junction applied during transient simulation of a HVAC air-side system. In: Journal of Building Performance Simulation, v. 11, n. 1 (December 2017).
- (2020): Inhibition effect and mechanism of polyacrylamide for steel corrosion in simulated concrete pore solution. In: Construction and Building Materials, v. 259 (October 2020).
- (2018): Optimizing the topologies of heating, ventilation, and air-conditioning water systems in supertall buildings: A pilot study. In: Science and Technology for the Built Environment, v. 24, n. 4 (March 2018).
- (2016): A fast method to predict the demand response peak load reductions of commercial buildings. In: Science and Technology for the Built Environment, v. 22, n. 6 (August 2016).
- (2016): Optimal demand response strategy of a portfolio of multiple commercial buildings: Methods and a case study. In: Science and Technology for the Built Environment, v. 22, n. 6 (August 2016).
- (2015): HVAC terminal hourly end-use disaggregation in commercial buildings with Fourier series model. In: Energy and Buildings, v. 97 (June 2015).
- (2016): A new method for calculating the thermal effects of irregular internal mass in buildings under demand response. In: Energy and Buildings, v. 130 (October 2016).
- (2018): Measures to improve energy demand flexibility in buildings for demand response (DR): A review. In: Energy and Buildings, v. 177 (October 2018).
- (2018): A lamination model for forming simulation of woven fabric reinforced thermoplastic prepregs. In: Composite Structures, v. 196 (July 2018).
- (2020): Investigation of the Influence of Foundation Deformability on Reinforced Soil Retaining Walls Using Centrifuge Model Tests. In: Soil Mechanics and Foundation Engineering, v. 57, n. 2 (May 2020).
- (2020): Feasibility and corrosion inhibition efficacy of zeolite-supported lauric acid imidazoline as corrosion inhibitor in cementitious mortar. In: Construction and Building Materials, v. 250 (July 2020).
- (2015): Optimizing the Alignment of Inspection Data from Track Geometry Cars. In: Computer-Aided Civil and Infrastructure Engineering, v. 30, n. 1 (December 2015).
- (2019): Large-scale model experiment and numerical simulation on convergence deformation of tunnel excavating in composite strata. In: Tunnelling and Underground Space Technology, v. 94 (December 2019).
- (2019): Influence of sulfate salt type on passive film of steel in simulated concrete pore solution. In: Construction and Building Materials, v. 223 (October 2019).
Structurae cooperates with
