Procedia Structural Integrity - 2016

Publié:	2016

Articles dans ce numéro

Auteur(s)	Titre	Page(s)
Taştan, A. / Yolum, U. / Güler, M. A. / Zaccariotto, M. / Galvanetto, U.	A 2D Peridynamic Model for Failure Analysis of Orthotropic Thin Plates Due to Bending	261-268
Grégoire, David / Lefort, Vincent / Nouailletas, Olivier / Pijaudier-Cabot, Gilles	2D-lattice modelling of crack propagation induced by fluid injection in heterogeneous quasi-brittle materials	2698-2705
Perl, M. / Steiner, M.	3-D Stress Intensity Factors due to Full Autofrettage for Inner Radial or Coplanar Crack Arrays and Ring Cracks in a Spherical Pressure Vessel	3625-3646
Hein, J. / Kuna, M.	3D J-integral for functionally graded and temperature dependent thermoelastic materials	2246-2254
Cherny, S. G. / Lapin, V. N.	3D model of hydraulic fracture with Herschel-Bulkley compressible fluid pumping	2479-2486
Bacaicoa, I. / Luetje, M. / Wicke, M. / Geisert, A. / Zeismann, F. / Fehlbier, M. / Brueckner-Foit, A.	3D Morphology of Al5FeSi inclusions in high Fe-content Al-Si-Cu Alloys	2269-2276
Maruschak, P. O. / Konovalenko, I. V. / Vuherer, T. / Panin, S. V. / Berto, F. / Danyliuk, I. M. / Menou, A.	Analysis and automated fatigue damage evaluation of a 17Mn1Si pipeline steel	1928-1935
Gutknecht, Florian / Steinbach, Frank / Hammer, Tobias / Clausmeyer, Till / Volk, Wolfram / Tekkaya, A. Erman	Analysis of shear cutting of dual phase steel by application of an advanced damage model	1700-1707
Perez Ipiña, Juan E. / Berejnoi, Carlos	Analysis of specimen size conversion in the ductile to brittle transition region of ferritic steels	769-776
Mayer, Uwe	Analysis of the Distribution of Fracture Toughness Values measured with 1T C(T) Specimens at Loading Rates higher than dK/dt=105 MPa√m s-1	1569-1576
Nenad, Mitrović / Ivan, Tanasić / Dušan, Šarac / Milošević, Miloš / Mišković, Žarko / Tihaček-Šojić, Ljiljana / Sedmak, Aleksandar	Analysis of the effect of implant distance from the surrounding structure, in the PMMA block model	1260-1265
Felli, F. / Brotzu, A. / Pilone, D.	Analysis of the fracture criticality of biphasic brass	2959-2965
Vukojević, Nedeljko / Gubeljak, Nenad / Terzic, Muamer / Hadžikadunić, Fuad	Analysis of the impact of position in fatigue cracks on the fracture toughness of thick-walled pressure vessel material	2982-2988
Markides, Christos F. / Kourkoulis, Stavros K.	Anisotropic discs loaded by parabolically distributed pressure	2659-2666
Ishihara, Kenichi / Hamada, Takeshi / Kikuya, Naohiro / Meshii, Toshiyuki	Applicability Of Modified Ritchie-Knott-Rice Failure Criterion To Predict The Onset Of Cleavage Fracture For The Test Specimen With Residual Stress Introduced To The Crack Tip	728-735
Scibetta, Marc	Application of a new cleavage fracture framework to ferritic steels	1610-1618
Hojo, Kiminobu / Ogawa, Naoki / Hirota, Takatoshi / Yoshimoto, Kentaro / Nagoshi, Yasuto / Kawabata, Shinichi	Application of Coupled Damage and Beremin Model to Ductile-Brittle Transition Temperature Region Considering Constraint Effect	1643-1651
Forget, Pierre / Marini, Bernard / Vincent, Ludovic	Application of local approach to fracture of an RPV steel: effect of the crystal plasticity on the critical carbide size	1660-1667
Bailey, P. B. S. / Higham, M.	Application of strain-controlled fatigue testing methods to polymer matrix composites	128-135
James, M. N. / Hattingh, D. G. / Asquith, D. / Newby, M. / Doubell, P.	Applications of Residual Stress in Combatting Fatigue and Fracture	11-25
Karanika, M. / Georgiou, D. / Darmanis, S. / Papadogoulas, A. / Pasiou, E. D. / Kourkoulis, S. K.	Assessing osteosynthesis techniques for pelvic fractures using Digital Image Correlation	1252-1259
Talemi, Reza H. / Brownb, Solomon / Martynov, Sergey / Mahgereftehb, Haroun	Assessment of brittle fractures in CO2 transportation pipelines: A hybrid fluid-structure interaction model	2439-2446
Qian, Xudong / Chen, Shuang / Ahmed, Aziz	Assessment of Cleavage Fracture in Specimens with a Curved Crack Front for High-Strength Steels in Offshore Applications	2046-2053
Choudhury, S. / Acharyya, S. K. / Dhar, S.	Assessment of constraint independence and temperature dependence of critical fracture energy, Gfr	736-743
Ševeček, Oldřich / Kotoul, Michal / Leguillon, Dominique / Martin, Eric / Bermejo, Raul	Assessment of crack-related problems in layered ceramics using the finite fracture mechanics and coupled stress-energy criterion	2014-2021
Cucinotta, F. / Guglielmino, E. / Risitano, G. / Sfravara, F.	Assessment of Damage Evolution in Sandwich Composite Material Subjected to Repeated Impacts by Means Optical Measurements	3660-3667
Felger, J. / Becker, W.	Asymptotic near-field analysis of wedges in anisotropic composite plates using first-order shear deformation theory	2504-2511
Larisa, Stepanova / Ekaterina, Yakovleva	Asymptotic Stress Field in the Vicinity of the Mixed-Mode Crack in Damaged Materials Under Creep Conditions	793-800
Klusak, Jan / Krepl, Ondrej / Profant, Tomas	Behaviour of a crack in a corner or at a tip of a polygon-like particle	1912-1919
Markides, Ch. F. / Pasiou, E. D. / Kourkoulis, S. K.	The bi-material circular disc compressed between the jaws of the ISRM standardized apparatus for the Brazilian test	2881-2888
Brünig, Michael / Gerkea, Steffen / Schmidt, Marco	Biaxial Experiments and Numerical Simulations on Damage and Fracture Mechanisms in Ductile Metals at Different Loading Conditions	3109-3116
Perelmuter, Mikhail	Bridged crack model of interfacial toughness	2030-2037
Stein, N. / Weißgraeber, P. / Becker, W.	Brittle failure in adhesive lap joints - a general Finite Fracture Mechanics approach	1967-1974
He, Junjing / Sandström, Rolf	Brittle rupture of austenitic stainless steels due to creep cavitation	863-870
Nourazar, M. / Ayatollahi, M.	Calculation of stress intensity factor in a non-homogeneous orthotropic half-plane weakened by moving cracks	2415-2423
Metaxa, Z. S. / Pasiou, E. D. / Dakanali, I. / Stavrakas, I. / Triantis, D. / Kourkoulis, S. K.	Carbon nanotube reinforced mortar as a sensor to monitor the structural integrity of restored marble epistyles under shear	2833-2840
Pascoe, J. A. / Alderliesten, R. C. / Benedictus, R.	Characterising resistance to fatigue crack growth in adhesive bonds by measuring release of strain energy	80-87
de Sousa Santos, Osmar / da Silva, Maria Margareth / Pichon, Luc / Rigo, Odair Doná / Otubo, Jorge	Characterization of a NiTi SMA wire treated by nitrogen plasma based ion implantation (PBII)	1443-1450
Wicke, M. / Luetje, M. / Bacaicoa, I. / Brueckner-Foit, A.	Characterization of Casting Pores in Fe-rich Al-Si-Cu Alloys by Microtomography and Finite Element Analysis	2643-2649
Kim, Dong-Jun / Lee, Han-Sang / Je, Jin-Ho / Kim, Yun-Jae / Ainsworth, Robert A. / Budden, Peter J.	Characterization of elastic-plastic-creep crack-tip stress fields under load and displacement control	832-839
Stuparu, Florin Adrian / Apostol, Dragos Alexandru / Constantinescu, Dan Mihai / Picu, Catalin Radu / Sandu, Marin / Sorohan, Stefan	Cohesive and XFEM evaluation of adhesive failure for dissimilar single-lap joints	316-325
Funari, Marco Francesco / Greco, Fabrizio / Lonetti, Paolo	A cohesive finite element model based ALE formulation for z-pins reinforced multilayered composite beams	452-459
Galkiewcz, Jaroslaw	Cohesive model application to micro-crack nucleation and growth	1619-1626
Stigh, Ulf / Biel, Anders / Svensson, Daniel	Cohesive zone modelling and the fracture process of structural tape	235-244
Bennati, Stefano / Colonna, Davide / Valvo, Paolo S.	A cohesive-zone model for steel beams strengthened with pre-stressed laminates	2682-2689
Msolli, Sabeur / Ben Bettaieb, Mohamed / Abed-Meraim, Farid	Combined effect of damage and plastic anisotropy on the ductility limit of thin metal sheets	3577-3584
Dittmann, F. / Varfolomeev, I.	Comparison of analytical methods for the consideration of thermal stresses in the engineering failure assessment	2974-2981
Moore, Philippa / Hutchison, Emily	Comparison of J Equations for SENT Specimens	3743-3751
Ruffing, C. / Ivanisenko, Yu. / Kerscher, E.	A comparison of the fatigue and fracture behavior of high strength ultrafine grained medium carbon steel SAE 1045 with high strength bearing steel SAE 52100	3240-3247
Gerin, Benjamin / Pessard, Etienne / Morel, Franck / Verdu, Catherine	Competition Between Surface Defects and Residual Stresses On Fatigue Behaviour of Shot Peened Forged Components	3226-3232
Stepanova, Larisa / Roslyakov, Pavel	Complete Williams Asymptotic Expansion Near The Crack Tips of Collinear Cracks of Equal Lengths in an Infinite Plane Medium	1789-1796
Sadek, Mohamed / Bergström, Jens / Hallbäck, Nils / Burman, Christer	Computation of and testing crack growth at 20 kHz load frequency	1164-1172
Conte, A. Lo / Biffi, C. A. / Tuissi, A. / Ali, A.	Computational Model for Delamination Growth at SMA-GFRP Interface of Hybrid Composite	1538-1545
Holopainen, Sami / Kouhia, Reijo / Könnö, Juho / Saksala, Timo	Computational modelling of transversely isotropic high-cycle fatigue using a continuum based model	2718-2725
Özüpek, Şebnem / Iyidiker, Çağrı	Computational Techniques to Predict Crack Growth in Nonlinear Viscoelastic Materials	2623-2630
Kauppila, Petteri / Kouhia, Reijo / Ojanperä, Juha / Saksala, Timo / Sorjonen, Timo	A continuum damage model for creep fracture and fatigue analyses	887-894
Yu, Haiyang / Olsen, Jim Stian / He, Jianying / Zhang, Zhiliang	Continuum level simulation of the grain size and misorientation effects on hydrogen embrittlement in nickel	565-572
Uenishi, Koji / Shigeno, Naoyuki / Sakaguchi, Shintaro / Yamachi, Hiroshi / Nakamori, Junichiro	Controlled disintegration of reinforced concrete blocks based on wave and fracture dynamics	350-357
Libonati, Flavia / Vergani, Laura	Cortical Bone as a Biomimetic Model for the Design of New Composites	1319-1326
Citarella, R. / Lepore, M. / Perrella, M. / Sepe, R. / Cricrì, G.	Coupled FEM-DBEM Simulation of 3D Crack Growth under Fatigue Load Spectrum	2631-2642
Firrao, Donato / Matteis, Paolo / Sapora, Alberto / Cornetti, Pietro / Carpinteri, Alberto	A coupled FFM model to interpret fracture toughness values for brittle materials	1983-1990
Sapora, Alberto / Cornetti, Pietro / Carpinteri, Alberto / Mantič, Vladislav	Crack deflection in brittle materials by Finite Fracture Mechanics	1975-1982
Curà, Francesca / Mura, Andrea / Rosso, Carlo	Crack propagation behavior in planet gears	3610-3616
Riemer, Andre / Richard, Hans Albert	Crack Propagation in Additive Manufactured Materials and Structures	1229-1236
Vafa, J. P. / Fariborz, S. J.	Crack propagation in layers under small-scale yielding	3447-3458
Carvalho, André L. M. / Martins, Juliana P. / Salvati, Enrico / Sui, Tan / Korsunsky, Alexander M.	Crack surface morphology and grain misorientation in fatigued aluminium alloy AA7050 samples after interrupted ageing and retrogression-reageing treatments	3697-3704
Delsart, David / Portemont, Gérald / Waimer, Matthias	Crash Testing of a CFRP Commercial Aircraft Sub-Cargo Fuselage Section	2198-2205
Hirakata, Hiroyuki / Kotoge, Ryota / Kameyama, Takumi / Kondo, Toshiyuki / Sakihara, Masayuki / Minoshima, Kohji	Creep crack propagation behavior in submicron gold films	1335-1342
Esposito, L. / Bonora, N. / De Vita, G.	Creep modelling of 316H stainless steel over a wide range of stress	927-933
He, Junjing / Sandström, Rolf / Vujic, Stojan	Creep, low cycle fatigue and creep-fatigue properties of a modified HR3C	871-878
Ab Razak, N. / Davies, C. M. / Nikbin, K. M.	Creep-fatigue crack growth behaviour of P91 steels	855-862
Mehmanparast, Ali / Davies, Catrin M. / Nikbin, Kamran	Creep-Fatigue Crack Growth Testing and Analysis of Pre-strained 316H Stainless Steel	785-792
Felli, F. / Lupi, C.	Critical Issues on Cast Iron Pipelines	2966-2973
de Souza, Rodolfo F. / Ruggieri, Claudio / Zhang, Zhilhiang	CTOD estimation procedure for clad pipe girth welds subjected to bending load	2068-2075
Fradkov, A. L. / Khantuleva, T. A.	Cybernetic model of the shock induced wave evolution in solids	994-1001
Wittke, P. / Walther, F.	Cyclic Deformation Behavior of Friction Drilled Internal Threads in AlSi10Mg and AZ31 Profiles	3264-3271
Bannikov, Mikhail V. / Naimark, Oleg B.	Damage evolution in metals under the gigacycle fatigue loading due to the contact with surface-active liquid	1071-1076
Petráš, R. / Škorík, V. / Polak, J.	Damage Evolution in Thermomechanical Loading of Stainless Steel	3407-3414
Li, Zaidao / Limodin, Nathalie / Tandjaoui, Amina / Quaegebeur, Philippe / Witz, Jean-François / Balloy, David	Damage investigation in A319 aluminum alloy by digital image correlation during in-situ tensile tests	3415-3422
Ribeiro, João / Santiago, Aldina / Rigueiro, Constança	Damage model calibration and application for S355 steel	656-663
Froustey, Catherine / Panteleev, Ivan / Lyapunova, Elena / Naimarkb, Oleg	Defect induced shear instability and ASB failure in metals	1959-1966
Melin, Solveig / Hansson, Per / Ahadi, Aylin	Defect sensitivity of single-crystal nano-sized Cu beams	1351-1358
Brighenti, Roberto / Spagnoli, Andrea / Carpinteri, Andrea / Artoni, Federico	Defect tolerance in soft materials	2788-2795
Morozov, V. A. / Lukin, A. A. / Atroshenko, S. A. / Gribanov, D. A. / Petrov, Yu. V.	Deformation and fracture of metal ring samples under the explosion of conductors	1002-1006
Simon, Ido / Banks-Sills, Leslie / Fourman, Victor / Eliasi, Rami	Delamination Propagation and Load Ratio Effects in DCB MD Woven Composite Specimens	205-212
Hutař, Pavel / Poduška, Jan / Chlupová, Alice / Šmíd, Miroslav / Kruml, Tomáš / Náhlík, Luboš	Description of short fatigue crack propagation under low cycle fatigue regime	3010-3017
Costanza, Girolamo / Tata, Maria Elisa	Design and characterization of a small-scale solar sail deployed by NiTi Shape Memory actuators	1451-1456
Nardo, R. Molica / Cerniglia, D. / Lombardo, P. / Pecoraro, S. / Infantino, A.	Detection, characterization and sizing of hydrogen induced cracking in pressure vessels using phased array ultrasonic data processing	581-588
Kolitsch, Stefan / Gänser, Hans-Peter / Pippan, Reinhard	Determination of crack initiation and crack growth stress-life curves by fracture mechanics experiments and statistical analysis	3026-3039
Bär, Jürgen	Determination of dissipated Energy in Fatigue Crack Propagation Experiments with Lock-In Thermography and Heat Flow Measurements	2105-2112
La Rosa, G. / Lo Savio, F. / Pedullà, E. / Rapisarda, E.	Developing of a new device for static and dynamic tests of Ni-Ti instruments for root canal treatment	1303-1310
Kolyshkin, Anton / Grigorescu, Andrei / Kaufmann, Edgar / Zimmermann, Martina / Christ, Hans-Jürgen	Development of a probabilistic model for the prediction of fatigue life in the very high cycle fatigue (VHCF) range based on inclusion population	1085-1092
Ali, Dilawar / Shahzad, Amer / Khan, Tanveer A.	Development of Fatigue Loading Spectra from Flight Test Data	3296-3304
Kawata, Itsuki / Yoshizu, Shuhei / Nakai, Hiroaki / Shibanuma, Kazuki / Aihara, Shuji	Development of New Formulation and Likelihood Function on Probabilistic Fracture Initiation Model	2463-2470
Hu, W. / Jones, R. / Kinloch, A. J.	Discussion of the Stress Ratio Effect on the Fatigue Delamination Growth Characterization in FRP Composite Structures	66-71
Aurore, Nicolas / Julien, Jumel	Double cantilever beam tests on a viscoelastic adhesive: effects of the loading rate	269-276
Hassani, Alireza / Faal, Reza Teymoori	Dugdale’s Model for Plastic Zone Size of Interacting Cracks under Anti-plane Deformation	2424-2431
Petrov, Yuri / Kazarinov, Nikita / Bratov, Vladimir	Dynamic crack propagation: quasistatic and impact loading	389-394
Coles, Laurence A. / Tilton, Craig / Roy, Anish / Shukla, Arun / Silberschmidt, Vadim V.	Dynamic fracture in carbon-fibre composites: Air-blast loading	417-421
Coles, Laurence A. / Roy, Anish / Voronov, Leonid / Semyonov, Sergey / Nikhamkin, Mikhail / Silberschmidt, Vadim V.	Dynamic Fracture in Carbon-fibre Composites: Effect of Steel and Ice Projectiles	366-372
Kopp, Jean-Benoît / Fond, Christophe / Schmittbuhl, Jean / Noel, Olivier	Dynamic fracture in rubber toughened polymers: the influence of the fracture surface roughness	468-476
Botvina, L. R. / Gryaznov, E. F.	Dynamic fragmentation of shells: scale effects	373-380
Selyutina, N. / Petrov, Y.	The dynamic strength of concrete and macroscopic temporal parameter characterized in fracture process	438-445
Alexopoulos, Nikolaos D. / Proiou, Aggeliki / Examilioti, Theano / Kashaev, Nikolai / Riekehr, Stefan / Kourkoulis, Stavros K.	Effect of artificial aging on the mechanical performance of (Al-Cu) 2024 and (Al-Cu-Li) 2198 aluminum alloys	3782-3783
Hanaki, T. / Hayashi, Y. / Akebono, H. / Kato, M. / Sugeta, A.	Effect of compression Residual Stress on Fatigue Properties of Stainless Cast Steel	3143-3149
Benachour, M. / Benachour, N. / Benguediab, M.	Effect of compressive residual stress generated by plastic preload on fatigue initiation of 6061 Al-alloy	3090-3097
Alexopoulos, Nikolaos D. / Dietzel, Wolfgang	Effect of corrosion-induced hydrogen embrittlement and its degradation impact on tensile properties and fracture toughness of (Al-Cu-Mg) 2024 alloy	573-580
Uesugi, Akio / Hirai, Yoshikazu / Tsuchiya, Toshiyuki / Tabata, Osamu	Effect of Crystallographic Orientations on Fractures and Slip Occurrences at 500 °C of (110) Single Crystal Silicon Microstructures	1413-1420
Toribio, J. / Vergara, D. / Lorenzo, M.	The effect of heat treatments on the constituent materials of a nuclear reactor pressure vessel in hydrogen environment	622-625
Harati, Ebrahim / Svensson, Lars-Erik / Karlsson, Leif / Hurtig, Kjell	Effect of HFMI treatment procedure on weld toe geometry and fatigue properties of high strength steel welds	3483-3490
Berto, F. / Mutignani, F. / Pittarello, L.	Effect of hot-dip galvanization on the fatigue behaviour of welded structural steel	1813-1820
Rao, G. Sudhakar / Seifert, Hans-Peter / Ritter, Stefan / Spätig, Philippe / Que, Zaiqing	Effect of hydrogen on tensile behavior of low alloy steel in the regime of dynamic strain ageing	3399-3406
Borsato, T. / Berto, F. / Ferro, P. / Carollo, C.	Effect of in-mould inoculant composition on microstructure and fatigue behaviour of heavy section ductile iron castings	3150-3157
Åman, Mari / Okazaki, Saburo / Matsunaga, Hisao / Marquis, Gary B. / Remes, Heikki	The effect of interacting small defects on the fatigue limit of a medium carbon steel	3322-3329
Grigorescu, Andrei / Kolyshkin, Anton / Zimmermann, Martina / Christ, Hans-Jürgen	Effect of martensite content and geometry of inclusions on the VHCF properties of predeformed metastable austenitic stainless steels	1093-1100
Nishikawa, Hide-aki / Furuya, Yoshiyuki	Effect of Mean Stress on Small Fatigue Crack Growth Rate on Low Carbon Steel with Several Simulated HAZ Heat Treatment	3002-3009
Sumigawa, Takashi / Matsumoto, Kenta / Kitamura, Takayuki	Effect of Microscopic Structure on High-cycle Fatigue Damage in Polycrystalline Nano-copper	1375-1382
Henschel, S. / Dudczig, S. / Krüger, L. / Aneziris, C. G.	Effect of non-metallic inclusions and shrinkage cavities on the dynamic fracture toughness of a high-strength G42CrMo4 cast steel	358-365
Meisner, L. L. / Rotshtein, V. P. / Markov, A. B. / Meisner, S. N. / Yakovlev, E. V. / D’yachenko, F.	Effect of nonmetallic and intermetallic inclusions on crater formation on the surface of TiNi alloys under the electron-beam impact	1465-1472
Jung, Jaewoong / Ju, Yang / Morita, Yasuyuki / Toku, Yuki	Effect of pulsed electric current on the growth behavior of fatigue crack in Al alloy	2989-2993
Hannemann, R. / Sander, M.	Effect of Specimen Geometry and Press-Fit on the Stress Intensity Factor Solution for Scaled Wheelset Axles under Bending	2527-2534
Pilone, D. / Brotzu, A. / Felli, F.	Effect of surface modification on the stability of oxide scales formed on TiAl intermetallic alloys at high temperature	2291-2298
Tanaka, Keisuke / Oharada, Kazuya / Yamada, Daiki / Shimizu, Kenichi	Effect of test temperature on fatigue crack propagation in injection molded plate of short-fiber reinforced plastics	58-65
Tolea, F. / Sofronie, M. / Crisan, A. D. / Popescu, B. / Tolea, M. / Valeanu, M.	Effect of thermal treatments in Ni-Fe-Ga with Co substitutions and Ni-Mn-Ga melt spun ribbons	1473-1480
Seko, Yusuke / Imai, Yasuhito / Mitsuya, Masaki / Oguchi, Noritake / Minami, Fumiyoshi	Effects of crack configuration and residual stress on fracture driving force for welded joint with embedded flaw	1708-1715
Yamabe, Junichiro / Yoshikawa, Michio / Matsunaga, Hisao / Matsuoka, Saburo	Effects of hydrogen pressure, test frequency and test temperature on fatigue crack growth properties of low-carbon steel in gaseous hydrogen	525-532
Nakai, Y. / Shiozawa, D. / Kikuchi, S. / Obama, T. / Saito, H. / Makino, T. / Neishi, Y.	Effects of inclusion size and orientation on rolling contact fatigue crack initiation observed by laminography using ultra-bright synchrotron radiation	3117-3124
Lai, Junbiao / Huang, Hanzheng / Buising, Wijbe	Effects of microstructure and surface roughness on the fatigue strength of high-strength steels	1213-1220
Cadoni, Ezio / Dotta, Matteo / Forni, Daniele / Kaufmann, Hanspeter	Effects of strain rate on mechanical properties in tension of a commercial aluminium alloy used in armour applications	986-993
Kyaw, S. T. / Rouse, J. P. / Lu, J. / Sun, W.	Effects of surface roughness on thermo-mechanical fatigue life of a P91 power plant steel	664-672
Bennati, Stefano / Fisicaro, Paolo / Valvo, Paolo S.	An elastic-interface model for the mixed-mode bending test under cyclic loads	72-79
Sedmak, Simon / Algool, Mahdi / Sedmak, Aleksandar / Tatic, Uros / Dzindo, Emina	Elastic-plastic behaviour of welded joints during loading and unloading of pressure vessels	3546-3553
Hell, Sascha / Becker, Wilfried	Energy release rates at two perpendicularly meeting cracks by use of the Scaled Boundary Finite Element Method	2471-2478
Meshii, Toshiyuki / Yamaguchi, Teruhiro	Engineering Framework to Transfer the Lower Bound Fracture Toughness between Different Temperatures in the DBTT Region	697-703
Meshii, Toshiyuki / Ishihara, Kenichi	Engineering Framework To Transfer The Minimum Fracture Toughness In The DBTT Region Between SE(B) And 1T CT Specimens	704-711
Yamaguchi, Teruhiro / Higashino, Yuma / Meshii, Toshiyuki	Engineering Framework to Utilize Miniaturized Charpy Type SE(B) Specimens to Predict Jc of Full Sized Specimens	712-719
Wang, Yingyu / Susmel, Luca	Estimating the orientation of crack initiation planes under constant and variable amplitude multiaxial fatigue loading	3233-3239
Skalny, Pavel	Evaluation and Identifying the Ductile Fracture Area of X70 Steel from DWTT Broken Specimens	3727-3734
Davis, Claire / Knowles, Meg / Rajic, Nik / Swanton, Geoff	Evaluation of a Distributed Fibre Optic Strain Sensing System for Full-Scale Fatigue Testing	3784-3791
Bernardi, Patrizia / Ferretti, Daniele / Michelini, Elena / Sirico, Alice	Evaluation of crack width in RC ties through a numerical "range" model	2780-2787
Hu, Jia-nan / Fukahori, Takuya / Igari, Toshihide / Chuman, Yasuharu / Cocks, Alan C. F.	An evaluation of creep rupture strength of ferritic/austenitic dissimilar weld interfaces using cohesive zone modelling	934-941
Özden, Utku Ahmet / Jiang, Keng / Bezold, Alexander / Broeckmann, Christoph	Evaluation of Fatigue Crack Growth Performance in different Hardmetal Grades based on Finite Element Simulation	648-655
Kakiuchi, Toshifumi / Uematsu, Yoshihiko / Suzuki, Kentaro	Evaluation of fatigue crack propagation in dissimilar Al/steel friction stir welds	1007-1014
Amano, Toshihiko / Fujishiro, Taishi / Shinohara, Yasuhiro / Inoue, Takehiro	Evaluation of Pre-strain Effect on Abnormal Fracture Occurrence in Drop-Weight Tear Test for Linepipe Steel with High Charpy Energy	422-429
Varfolomeev, I. / Dittmann, F.	Examination of methods for the treatment of constraint effects within the FAD approach	761-768
La Rosa, Guido / Clienti, Carmelo / Mineo, Rosalia / Audenino, Alberto	Experimental analysis of pedicle screws	1244-1251
Płatek, Robert / Malinowski, Łukasz / Sekuła, Robert / Zwoliński, Piotr	Experimental and numerical analysis of microstructure damage in silica filled epoxy	285-292
Werner, Benjamin / Heyer, Horst / Sander, Manuela	Experimental and numerical investigation of fracture in fillet welds by cross joint specimens	2054-2067
Hemmi, Takuhiro / Shibanuma, Kazuki / Suzuki, Katsuyuki / Aihara, Shuji / Shirahata, Hiroyuki	Experimental and numerical investigation on relationship between grain size and arrest toughness in steels	2230-2237
Fehringer, Florian / Seidenfuß, Michael / Schuler, Xaver	Experimental and numerical investigations on limit strains in ductile fracture	3345-3352
Hertelé, Stijn / Van Gerven, Filip / Naib, Sameera / Gubeljak, Nenad / De Waele, Wim	Experimental and numerical slip line analysis of welded single-edge notched tension specimens	1763-1770
Bassi, F. / Saxena, A. / Conte, A. Lo / Beretta, S. / Cristea, M. E.	Experimental and simulated displacement in cracked specimen of P91 steel under creep conditions	911-918
Wcislik, Wiktor	Experimental determination of critical void volume fraction fF for the Gurson Tvergaard Needleman (GTN) model	1676-1683
Zhang, Zhinan / Wang, Wandong / Rans, Calvin / Benedictus, Rinze	An experimental investigation into pin loading effects on fatigue crack growth in Fibre Metal Laminates	3361-3368
Budzik, Michal K. / Jensen, Henrik M.	Experimental study of cracks at interfaces with voids	277-284
Sancho, A. / Cox, M. J. / Cartwright, T. / Aldrich-Smith, G. D. / Hooper, P. A. / Davies, C. M. / Dear, J. P.	Experimental techniques for ductile damage characterisation	966-973
Hu, Shaowei / Xu, Aiqing	Experimental validation and fracture properties analysis on wedge splitting concrete specimens with different initial seam-height ratios	2818-2832
Namdar, Abdoullah	Failure analysis of concrete frame - A numerical analysis	2796-2802
Blednova, Zh. M. / Rusinov, P. O. / Dmitrenko, D. V.	Failure analysis of screw propellers and increase of fail safety by surface modification with multicomponent materials with shape memory effect	1497-1505
Tretyakov, M. P. / Wildemann, V. E. / Lomakin, E. V.	Failure of materials on the postcritical deformation stage at different types of the stress-strain state	3721-3726
Moroni, Fabrizio / Alfano, Marco / Romoli, Luca	Fatigue analysis of adhesive joints with laser treated substrates	120-127
Salvati, Enrico / Zhang, Hongjia / Fong, Kai Soon / Paynter, Robert J. H. / Song, Xu / Korsunsky, Alexander M.	Fatigue and Fracture behaviour of AZ31b Mg alloy plastically deformed by Constrained Groove Pressing in the Presence of Overloads	3772-3781
Herrmann, Jenni / Rauert, Thes / Dalhoff, Peter / Sander, Manuela	Fatigue and fracture mechanical behaviour of a wind turbine rotor shaft made of cast iron and forged steel	2951-2958
Rocchini, Marco / Davies, Catrin M. / Dean, David W. / Nikbin, Kamran M.	Fatigue and Fracture Resistance of 316H Stainless Steel With Prior Creep Damage	879-886
Chastand, Victor / Tezenas, Astrid / Cadoret, Yannick / Quaegebeur, Philippe / Maia, Wilson / Charkaluk, Eric	Fatigue characterization of Titanium Ti-6Al-4V samples produced by Additive Manufacturing	3168-3176
Angelova, Donka / Yordanova, Rozina / Yankova, Svetla	Fatigue crack development in a low-carbon steel. Microstructure influence. Modelling	2726-2733
Reschetnik, W. / Brüggemann, J.-P. / Aydinöz, M. E. / Grydin, O. / Hoyer, K.-P. / Kullmer, G. / Richard, H. A.	Fatigue crack growth behavior and mechanical properties of additively processed EN AW-7075 aluminium alloy	3040-3048
Correia, José A. F. O. / de Jesus, Abilio M. P. / Alves, Ana S. F. / Lesiuk, Grzegorz / Tavares, Paulo J. S. / Moreira, Pedro M. G. P.	Fatigue crack growth behaviour of the 6082-T6 aluminium using CT specimens with distinct notches	3272-3279
Toribio, Jesús / Matos, Juan-Carlos / González, Beatriz / Escuadra, José	Fatigue crack growth in round bars for rock anchorages: the role of residual stresses	2734-2741
Loghin, Adrian / Ananthasayanam, Balajee / LeMonds, Jeff / Subramaniyan, Arun / Viana, Felipe	Fatigue Crack Growth Life Assessment for Industrial Applications using Re-meshing and Bayesian Hybrid Techniques	2487-2494
Kullmer, Gunter / Reschetnik, Wadim / Schramm, Britta / Richard, Hans-Albert	Fatigue crack growth near regions with differing stiffness	2994-3001
Dirik, Haydar / Yalçinkaya, Tuncay	Fatigue Crack Growth Under Variable Amplitude Loading Through XFEM	3073-3080
Nikitin, Alexander / Palin-Luc, Thierry / Shanyavskiy, Andrey	Fatigue crack initiation and growth on an extruded titanium alloy in gigacycle regime: comparison between tension and torsion loadings	1125-1132
Yasniy, P. / Glado, S. / Iasnii, V.	Fatigue crack nucleation and propagation in aluminum alloy plates with cold expanded holes	3280-3287
Lesiuk, Grzegorz / Correia, José A. F. O. / de Jesus, A. M. P. / Kucharski, Paweł	Fatigue crack propagation behavior of old puddle iron including crack closure effects	3218-3225
Kondo, Toshiyuki / Shin, Akihiro / Hirakata, Hiroyuki / Minoshima, Kohji	Fatigue crack propagation properties of submicron-thick freestanding copper films in vacuum environment	1359-1366
Toribio, Jesús / González, Beatriz / Matos, Juan-Carlos	Fatigue cracking in high-strength cold-drawn pearlitic steel wires for anchorage in rocks	2330-2337
Bertini, L. / Frendo, F. / Marulo, G.	Fatigue endurance of welded joints subjected to different blocks of bending and torsion loading	3531-3538
Bertini, L. / Le Bone, L. / Santus, C. / Chiesi, F. / Tognarelli, L.	Fatigue investigation at high load ratio R of a quenched and tempered chromium molybdenum steel	681-689
Su Woo, Chang / Park, Hyun Sung	Fatigue Life Evaluation of Rubber-Clay Nanocomposites	2173-2181
Corigliano, P. / Crupi, V. / Epasto, G. / Guglielmino, E. / Risitano, G.	Fatigue life prediction of high strength steel welded joints by Energy Approach	2156-2163
Shiozawa, Daiki / Inagawa, Tsuyoshi / Washio, Takaya / Sakagami, Takahide	Fatigue limit estimation of stainless steels with new dissipated energy data analysis	2091-2096
Benedetti, M. / Cazzolli, M. / Fontanari, V. / Leoni, M.	Fatigue limit of Ti6Al4V alloy produced by Selective Laser Sintering	3158-3167
Rolland, H. / Saintier, N. / Lenoir, N. / King, A. / Robert, G.	Fatigue mechanisms description in short glass fibre reinforced thermoplastic by microtomographic observations	301-308
Di Cocco, Vittorio / Iacoviello, Francesco / Natali, Stefano	Fatigue microstructural evolution in pseudo elastic NiTi alloy	1457-1464
Jaureguizahar, Sebastián M. / Chapetti, Mirco D. / Yawny, Alejandro A.	Fatigue of NiTi shape memory wires	1427-1434
Tyc, O. / Pilch, J. / Šittner, P.	Fatigue of superelastic NiTi wires with different plateau strain	1489-1496
Nagashima, Nobuo / Sawaguchi, Takahiro / Ogawa, Kazuyuki	Fatigue properties of Fe-28Mn-6Si-5Cr-0.5NbC alloy	1435-1442
Kagami, S. / Ueno, A. / Miyakawa, S. / Miyamoto, N. / Ishibashi, N. / Guennec, B.	Fatigue properties of high-strength steel in diesel oil	1738-1745
Kazantsev, A. G. / Kakhadze, M. G. / Soin, K. A. / Rodin, I. Y. / Nasluzov, S. N.	Fatigue strength of PF-1 coil helium inlet with weld defects.	3562-3568
Michalcová, Lenka / Růžek, Roman	Fatigue test of an integrally stiffened panel: Prediction and crack growth monitoring using acoustic emission	3049-3056
Musiari, F. / Pirondi, A. / Moroni, F. / Giuliese, G. / Belcari, J. / Zucchelli, A. / Brugo, T. M. / Minak, G. / Ragazzini, C.	Feasibility study of adhesive bonding reinforcement by electrospun nanofibers	112-119
Fantilli, Alessandro P. / Gorino, Andrea / Chiaia, Bernardino	Fiber volume fraction and ductility index in fiber-reinforced concrete round determined panels	2857-2864
Nishioka, Yo / Shibanuma, Kazuki / Suzuki, Katsuyuki / Yanagimoto, Fuminori	Finite element model to simulate crack propagation based on local fracture stress criterion	2558-2565
Kim, Dong-Jun / Bae, Kyung-Dong / Lee, Han-Sang / Kim, Yun-Jae / Park, Goon-Cherl	Finite element simulation of creep crack growth using combined plastic-creep damage model	825-831
Ancellotti, Simone / Benedetti, Matteo / Dallago, Michele / Fontanari, Vigilio	Fluid Pressurization and Entrapment Effects on the SIFs of Cracks produced under lubricated Rolling-Sliding Contact Fatigue	3098-3108
Rusinov, P. O. / Blednova, Zh. M. / Balaev, E. U. / Dmitrenko, D. V.	Formation of composite layers TiNiZr-cBN-Co, working in conditions of cyclic loading and reverse friction	1506-1513
Kikuchi, S. / Ota, S. / Akebono, H. / Omiya, M. / Komotori, J. / Sugeta, A. / Nakai, Y.	Formation of nitrided layer using atmospheric-controlled IH-FPP and its effect on the fatigue properties of Ti-6Al-4V alloy under four-point bending	3432-3438
Molent, Loris / Spagnoli, Andrea / Carpinteri, Andrea / Jones, Rhys	Fractals and the lead crack airframe lifing framework	3081-3089
Nourazar, M. / Ayatollahi, M. / Miandari, J. / Varasteh, S.	Fracture analysis of a cracked orthotropic strip bonded to a magneto-electro-elastic layer	3423-3431
Berto, Filippo / Campagnolo, Alberto / Ayatollahi, Majid / Barnoush, Afrooz	Fracture assessment of graphite components weakened by rounded V-notches and subjected to static multiaxial loading	1805-1812
Gao, Xing / Shi, Zhijun / Liu, Changqing / Yang, Guang / Silberschmidt, Vadim V.	Fracture Behaviour of Bacterial Cellulose Hydrogel: Microstructural Effect	1237-1243
Tarpani, J. R. / Alves, C. L. / Oliveira, J. S. / Vidoto, E. L. G. / Tannús, A.	Fracture characterization of continuous fibre-reinforced polymer matrix composite laminates by Nuclear Magnetic Resonance	136-143
El-Sehily, B. M.	Fracture Mechanics in Ancient Egypt	2921-2928
Taylor, David	Fracture Mechanics in Biology and Medicine	42-49
Kamaludin, M. A. / Patel, Y. / Blackman, B. R. K. / Williams, J. G.	Fracture mechanics testing for environmental stress cracking in thermoplastics	227-234
Contino, M. / Andena, L. / Rink, M. / Colombo, A. / Marra, G.	Fracture of high-density polyethylene used for bleach bottles	213-220
Piccotin, Alberto / Marsavina, Liviu / Berto, Filippo / Negru, Radu	Fracture parameters determination of polyurethane materials for application of SED criteria to notched components	1861-1869
Frutos, E. / Karlik, M. / Polcar, T.	Fracture toughness determination by repetitive nano-impact testing in Cu/W nanomultilayers with length-scale-dependent films properties	1391-1404
Hesse, Ann-Christin / Nitschke-Pagel, Thomas / Dilger, Klaus	Fracture Toughness of Electron Beam Welded Fine Grain Steels	3523-3530
Boroński, Dariusz / Kotyk, Maciej / Maćkowiak, Paweł	Fracture Toughness of Explosively Welded Al/Ti Layered Material in Cryogenic Conditions	3764-3771
Rauert, Thes / Herrmann, Jenni / Dalhoff, Peter / Sander, Manuela	Fretting fatigue induced surface cracks under shrink fitted main bearings in wind turbine rotor shafts	3601-3609
Bastola, A. / Wang, J. / Shitamoto, H. / Mirzaee-Sisan, A. / Hamada, M. / Hisamune, N.	Full- and small-scale tests on strain capacity of X80 seamless pipes	1894-1903
Meneghetti, G. / Ricotta, M. / Sanità, M. / Refosco, D.	Fully Reversed Axial Notch Fatigue Behaviour of Virgin and Recycled Polypropylene Compounds	2255-2262
Petrov, Yuri / Smirnov, Ivan	General effects of pulse electric breakdown of dielectric gaps and dynamic failure of continuous media	430-437
Lee, Han-Sang / Kim, Dong-Jun / Je, Jin-Ho / Kim, Yun-Jae / Ainsworth, Robert A. / Budden, Peter J.	General estimation equation of transient C(t) under load and displacement control	817-824
Brugger, Charles / Palin-Luc, Thierry / Osmond, Pierre / Blanc, Michel	Gigacycle fatigue behavior of a cast aluminum alloy under biaxial bending: experiments with a new piezoelectric fatigue testing device	1173-1180
Naimark, Oleg / Palin-Luc, Thierry	Gigacycle fatigue: non-local and scaling aspects of damage localization, crack initiation and propagation	1143-1148
Meneghetti, Giovanni / Ricotta, Mauro / Atzori, Bruno	The Heat Energy Dissipated in a Control Volume to Correlate the Fatigue Strength of Bluntly and Severely Notched Stainless Steel Specimens	2076-2083
Ubertalli, G. / D’Aiuto, F. / Plano, S. / De Caro, D.	High strain rate behavior of aluminum die cast components	3617-3624
Thielen, M. / Marx, M. / Sheikh-Amiri, M. / Boller, C. / Motz, C.	How microscopic stress and strain analysis can improve the understanding of the interplay between material properties and variable amplitude fatigue	3194-3201
Nykyforchyn, H. M. / Zvirko, O. I. / Tsyrulnyk, O. T.	Hydrogen assisted macrodelamination in gas lateral pipe	501-508
Toribio, J. / Lorenzo, M. / Vergara, D.	Hydrogen embrittlement susceptibility of prestressing steel wires: the role of the cold-drawing conditions	626-631
Baturin, A. / Lotkov, A. / Grishkov, V. / Rodionov, I. / Krukovskiy, K.	Hydrogen-induced failure of TiNi based alloy with coarse-grained and ultrafine-grained structure	1481-1488
Risitano, A. / D’Aveni, A. / Fargione, G. / Clienti, C.	Identification of local phenomena of plasticity in concrete under compression test	2123-2131
Rekik, W. / Ancelet, O. / Gardin, C.	Identification of the Weakest Metallurgical Zone on Fracture Behavior of an Undermatched Welded Joint	3491-3500
Kubit, Andrzej / Bucior, Magdalena / Zielecki, Władysław / Stachowicz, Feliks	The impact of heat treatment and shot peening on the fatigue strength of 51CrV4 steel	3330-3336
Kubit, Andrzej / Bucior, Magdalena / Zielecki, Władysław	The impact of the multiwall carbon nanotubes on the fatigue properties of adhesive joints of 2024-T3 aluminium alloy subjected to peel	334-341
Fortese, Giovanni / Carpinteri, Andrea / Di Cocco, Vittorio / Iacoviello, Francesco / Natali, Stefano / Ronchei, Camilla / Scorza, Daniela / Vantadori, Sabrina	Improved Zn-based coatings for ipersandelin steel products	2263-2268
Ahadi, Aylin / Hansson, Per / Melin, Solveig	Indentation of thin copper film using molecular dynamics and peridynamics	1343-1350
Aleksić, V. / Milović, Lj. / Aleksic, B. / Hemer, Abubkr M.	Indicators of HSLA steel behavior under low cycle fatigue loading	3313-3321
Muñoz-Reja, Mar / Távara, Luis / Mantič, Vladislav / Cornetti, Pietro	Influence of a neighbour fibre on the onset and growth of a fibre-matrix debond under biaxial loading. A study by Finite Fracture Mechanics at linear elastic interfaces	2022-2029
Meischel, M. / Stanzl-Tschegg, S. E. / Arcari, A. / Iyyer, N. / Phan, N.	Influence of Corrosive NaCl solution on Life times of 7075 Aluminum alloy under Combined Fatigue loading in the VHCF Regime	1077-1084
Kšiňan, Jozef / Vodička, Roman	The influence of friction on delamination in Fibre-Reinforced Composites, An SGBEM implementation.	197-204
Lo Savio, F. / Pedullà, E. / Rapisarda, E. / La Rosa, G.	Influence of heat-treatment on torsional resistance to fracture of nickel-titanium endodontic instruments	1311-1318
Schönbauer, B. M. / Yanase, K. / Endo, M.	Influence of intrinsic and artificial defects on the VHCF properties of 17-4PH stainless steel	1149-1155
Ebara, Ryuichiro	The influence of metallurgical factors on corrosion fatigue strength of stainless steels	517-524
Martinez-Ubeda, Ana I. / Griffiths, Ian / Karunaratne, Mudith S. A. / Flewitt, Peter E. J. / Younes, Charles / Scott, Tom	Influence of nominal composition variation on phase evolution and creep life of Type 316H austenitic stainless steel components	958-965
Lee, So-Dam / Lee, Han-Sang / Lee, Myeong-Woo / Kim, Yun-Jae / Ainsworth, Robert A. / Dean, David W.	The influence of plastic material property equations on the initial C(t) and J(t) in elastic-plastic-creep FE analysis	847-854
Everaerts, Joris / Verlinden, Bert / Wevers, Martine	The influence of the alpha grain size on internal fatigue crack initiation in drawn Ti-6Al-4V wires	1055-1062
Dahdah, Nora / Limodin, Nathalie / El Bartali, Ahmed / Witz, Jean-François / Seghir, Rian / Charkaluk, Eric / Buffiere, Jean-Yves	Influence of the Casting Process in High Temperature Fatigue of A319 Aluminium Alloy Investigated By In-Situ X- Ray Tomography and Digital Volume Correlation	3057-3064
Pokorný, Pavel / Náhlík, Luboš / Hutař, Pavel	Influence of variable stress ratio during train operation on residual fatigue lifetime of railway axles	3585-3592
Benamara, M. / Pluvinage, G. / Capelle, J. / Azari, Z.	Influence Yield Stress on Arrest Pressure in Pipe Predicted by CTOA	3337-3344
Murakoshi, Takuya / Shinozaki, Taichi / Suzuki, Ken / Miura, Hideo	Initial Degradation Process of Heat-resistant Materials Based on the Change of Crystallinity of Grains and Grain Boundaries	1383-1390
Mirone, G. / Corallo, D. / Barbagallo, R.	Interaction of strain rate and necking on the stress-strain response of uniaxial tension tests by Hopkinson bar	974-985
Ståhl, Per / Reheman, Wureguli	Interface instabilities of growing hydrides	589-596
Torskaya, Elena / Mezrin, Alexey	Interfacial fracture of thin elastic layers due to cyclic load	3459-3466
Takahashi, Yoshimasa / Aihara, Kazuya / Ashida, Itaru / Takuma, Masanori / Saitoh, Kenichi / Sato, Tomohiro / Higuchi, Kimitaka / Yamamoto, Yuta / Arai, Shigeo / Muto, Shunsuke	Interfacial fracture strength property of micro-scale SiN/Cu components	1367-1374
Laureys, A. / Petrov, R. / Verbeken, K.	Internal and surface damage after electrochemical hydrogen charging for ultra low carbon steel with various degrees of recrystallization	541-548
Ejaz, Muneeb / Daviesa, Catrin M. / Dean, David W.	Interpretation of creep crack growth data for ½ CMV steel weldments	903-910
Tretyakova, T. V. / Wildemann, V. E.	Interrelation between local strain jumps and temperature bursts due to the jerky flow in metals under the complicate loading conditions: experimental study by using the DIC-technique and the IR-analysis	3393-3398
Ould Moussa, Mohamed / Sauzay, Maxime	Introduction to the effect of the screening phenomenon of slip bands within grain microstructure	1692-1699
Unnikrishnan, Rahul / Northover, Shirley M. / Jazaeri, Hedieh / Bouchard, P. John	Investigating plastic deformation around a reheat-crack in a 316H austenitic stainless steel weldment by misorientation mapping	3501-3507
Millar, T. M. / Patel, Y. / Wang, H. / Chang, L. / Balint, D. S. / Williams, J. G.	An investigation of cutting resistance in stretched polymer films	190-196
Mutschler, Patrick / Sander, Manuela	Investigation of fatigue crack growth in a power plant steel under elevated temperatures	801-808
Giertler, A. / Krupp, U.	Investigation of the damage mechanisms during very high cycle fatigue (VHCF) of a tempered carbon steel	1207-1212
Mirzaali, M. J. / Libonati, F. / Vena, P. / Mussi, V. / Vergani, L. / Strano, M.	Investigation of the Effect of Internal Pores Distribution on the Elastic Properties of Closed-Cell Aluminum Foam: A Comparison with Cancellous Bone	1285-1294
Kawabata, Tomoya / Tagawa, Tetuya / Kayamori, Yoichi / Aihara, Shuji / Hagihara, Yukito	Investigation on the rotational deformation of SEB specimens with various crack length to width ratio	2772-2779
Isik, Kerim / Gerstein, Gregory / Gutknecht, Florian / Clausmeyer, Till / Nürnberger, Florian / Maier, Hans Jürgen / Tekkaya, A. Erman	Investigations of ductile damage in DP600 and DC04 deep drawing steel sheets during punching	673-680
Panin, S. V. / Maruschak, P. O. / Vlasov, I. V. / Sergeev, V. P. / Berto, F.	Inﬂuence of high intensity ion beam irradiation on impact toughness of 12Cr1MoV steel	403-408
Teimoori, Hossein / Faal, Reza Teymoori	Irwin’s plastic zone size assessment for interacting cracks in a circular plane subjected to anti-plane deformation	2432-2438
Matvienko, Yu. G. / Nikishkov, G. P.	J-A elastic-plastic crack tip field and the two-parameter fracture criterion	26-33
Muniz-Calvente, M. / Shlyannikov, V. N. / Meshii, T. / Giner, E. / Fernández-Canteli, A.	Joint evaluation of fracture results from distinct test conditions, implying loading, specimen size and geometry	720-727
Yasniy, O. / Pyndus, Yu. / Brevus, V. / Iasnii, V. / Lapusta, Y.	Lifetime estimation of superheater header	840-846
Bind, A. K. / Sunil, S. / Singh, R. N. / Tiwari, Abhishek / Chakravartty, J. K.	Load separation in 17 mm wide CT specimen of Zr-2.5Nb pressure tube material	3752-3757
Goldstein, R. V. / Osipenko, N. M.	Loading history and structure of fracture of material	2397-2404
Tiwari, Abhishek / Singh, R. N. / Ståhle, Per / Chakravartty, J. K.	A loss of constraint assessment using σ-V approach to describe the effect of crack depth on reference transition temperature T0	690-696
Pandey, Vaibhav / Chattopadhyay, K. / Santhi Srinivas, N. C. / Singh, Vakil	Low Cycle Fatigue behavior of AA7075 with surface gradient structure produced by Ultrasonic Shot Peening	3288-3295
Alang, N. A. / Davies, C. M. / Nikbin, K. M.	Low Cycle Fatigue Behaviour of Ex-Service P92 Steel at Elevated Temperature	3177-3184
Fujimoto, Koji / Hojo, Masahiro / Fujita, Akira	Low cycle fatigue of CFRP laminated composites due to repeated out-of-plane loading	182-189
Fekete, Balázs / Trampus, Péter / Jandova, Dagmar / Kasl, Josef / Jóni, Bertalan / Misják, Fanni / Radnóczi, György	Low cycle thermomechanical fatigue of VVER-440 reactor pressure vessel steels: Investigation the fatigue kinetics and development of a life assessment model	2164-2172
Sofronie, M. / Tolea, F. / Crisan, A. D. / Popescu, B. / Valeanu, M.	Magnetoelastic properties in polycrystalline ferromagnetic shape memory Heusler alloys	1530-1537
Tiwari, Abhishek / Singh, R. N. / Ståhle, Per / Chakravartty, J. K.	Master curve in upper region of ductile brittle transition: a modification based on local damage approach	1553-1560
Richard, H. A. / Eberlein, A.	Material characteristics at 3D-mixed-mode-loadings	1821-1828
Szávaia, Szabolcs / Bézi, Zoltán / Rózsahegyi, Peter	Material Characterization and Numerical Simulation of a Dissimilar Metal Weld	1023-1030
Chernyatin, A. S. / Matvienko, Yu. G. / Lopez-Crespo, P.	Mathematical and numerical correction of the DIC displacements for determination of stress field along crack front	2650-2658
Yanagimoto, Fuminori / Shibanuma, Kazuki / Kawabata, Tomoya / Suzuki, Katsuyuki / Aihara, Shuji	Measurement of local brittle fracture stress for dynamic crack propagation in steel	395-402
Carolan, Declan / Kinloch, A. J. / Ivankovic, A. / Sprenger, S. / Taylor, A. C.	Mechanical and fracture performance of carbon fibre reinforced composites with nanoparticle modified matrices	96-103
Sarre, Benjamin / Flouriot, Sylvain / Geandier, Guillaume / Panicaud, Benoit / Rancourt, Victor de	Mechanical behavior and fracture mechanisms of titanium alloy welded joints made by pulsed laser beam welding	3569-3576
Alexopoulos, Nikolaos D. / Proiou, Angeliki / Dietzel, Wolfgang / Blawert, Carsten / Heitmann, Volker / Zheludkevich, Mikhail / Kourkoulis, Stavros K.	Mechanical properties degradation of (Al-Cu-Li) 2198 alloy due to corrosion exposure	597-603
Miron, Matei-Constantin / Katzinger, Harald / Neudorfer, Severin / Pitz, Emil / Major, Zoltán	Mechanical testing and numerical predictions of the behavior of braided carbon fiber components	3593-3600
Dönges, B. / Fritzen, C.-P. / Christ, H.-J.	Mechanisms inhibiting short fatigue crack propagation at loading amplitudes close to the conventional fatigue limit	3305-3312
Pommier, S.	Memory effects in variable amplitude and multiaxial fatigue crack growth: an incremental approach	50-57
Crump, Timothy / Mummery, Paul / Jivkov, Andrey / Tran, Van-Xuan	A meso-scale approach to modelling stable dynamic crack propagation in glass under rate-dependent loading	381-388
Gardan, Julien / Makke, Ali / Recho, Naman	A Method to Improve the Fracture Toughness Using 3D Printing by Extrusion Deposition	144-151
Asako, Shohei / Kawabata, Tomoya / Aihara, Shuji / Kimura, Shintaro / Kagehira, Kiyoshi	Micro-processes of brittle fracture initiation in bainite steel manufactured by ausforming	3668-3675
Yalçinkaya, Tuncay / Cocks, Alan	Micromechanical cohesive zone relations for ductile fracture	1716-1723
Le, V. N. / Benabou, L. / Etgens, V. / Tao, Q. B.	Micromechanical model for describing intergranular fatigue cracking in a lead-free solder alloy	2614-2622
Esposito, L. / Pucillo, G. P. / Penta, F. / Rosiello, V.	Micromechanical study and simulation of the interlaminar failure of a woven composite laminate	1870-1877
Man, Jiří / Kuběna, Ivo / Smaga, Marek / Man, Ondřej / Järvenpää, Antti / Weidner, Anja / Chlup, Zdeněk / Polák, Jaroslav	Microstructural changes during deformation of AISI 300 grade austenitic stainless steels: Impact of chemical heterogeneity	2299-2306
Evard, Margarita E. / Volkov, Aleksandr A. / Belyaev, Fedor S. / Ignatova, Anna D. / Volkova, Natalia A.	Microstructural modelling of plastic deformation and defects accumulation in FeMn-based shape memory alloys	1546-1552
Konečná, Radomila / Nicoletto, Gianni / Kunz, Ludvík / Bača, Adrián	Microstructure and directional fatigue behavior of Inconel 718 produced by selective laser melting	2381-2388
Agbessi, Komlan / Saintier, Nicolas / Palin-Luc, Thierry	Microstructure-based study of the crack initiation mechanisms in pure copper under high cycle multiaxial fatigue loading conditions	3210-3217
Liu, Xuesong / Song, Wei / Yan, Zhongjie / Qiang, Wang / pan, Haibo	Misalignment effect on stress concentration of thickness mismatched plate structures	2038-2045
Shahverdi, Moslem / Vassilopoulos, Anastasios P. / Keller, Thomas	Mixed-Mode I/II fracture behavior of asymmetric composite joints	1886-1893
Vantadori, Sabrina / Carpinteri, Andrea / Fortese, Giovanni / Ronchei, Camilla / Scorza, Daniela	Mode I fracture toughness of fibre-reinforced concrete by means of a modified version of the two-parameter model	2889-2895
Campagnolo, Alberto / Berto, Filippo / Leguillon, Dominique	Mode II loading in sharp V-notched components: a comparison among some recent criteria for brittle fracture assessment	1845-1852
Hilgendorff, P.-M. / Grigorescu, A. / Zimmermann, M. / Fritzen, C.-P. / Christ, H.-J.	Modeling and simulation of temperature-dependent cyclic plastic deformation of austenitic stainless steels at the VHCF limit	1156-1163
Shibanuma, Kazuki / Yanagimoto, Fuminori / Namegawa, Tetsuya / Suzuki, Katsuyuki / Aihara, Shuji	Modeling of Brittle Crack Propagation/Arrest Behavior in Steel Plates	2598-2605
Fedelich, B. / Kühn, H.-J. / Rehmer, B. / Skrotzki, B.	Modeling the lifetime reduction due to the superposition of TMF and HCF loadings in cast iron alloys	2190-2197
Berto, F. / Campagnolo, A. / Chebat, F. / Cincera, M. / Welo, T.	Modelling and fatigue assessment of steel rollers with failure occurring at the weld root based on the local strain energy	3475-3482
Kinloch, A. J. / Jones, R. / Hu, W.	Modelling and predicting fatigue crack growth in structural adhesive joints	221-226
Caimmi, Francesco / Haddadi, Elyas / Choupani, Naghdali / Marano, Claudia / Andena, Luca	Modelling mixed-mode fracture in poly(methylmethacrylate) using peridynamics	166-173
Szávai, Szabolcs / Bézi, Zoltán / Dudra, Judit / Méhész, István	Modelling of Phased Array Ultrasonic Inspection of a Steam Generator Dissimilar Metal Weld	1015-1022
Peixoto, Daniel F. C. / de Castro, Paulo M. S. T.	Modelling of the fracture of a railway wheel	1904-1911
Mohammed, Idris K. / Kinloch, Anthony J. / Charalambides, Maria N.	Modelling the Peeling Behavior of Soft Adhesives	326-333
Brunner, Andreas J. / Mujtaba, Ahmad / Stelzer, Steffen / Jones, Rhys	Modified Hartman-Schijve fitting of mode I delamination fatigue data and the resulting variation in threshold values Gthr	88-95
Reichert, Thomas / Böhme, Wolfgang / Tlatlik, Johannes	Modified Shape of Dynamic Master Curves due to Adiabatic Effects	1652-1659
Ruggieri, Claudio / Dodds, Robert H.	A Modified Weibull Stress Approach to Predict Specimen Geometry Effects in a Pressure Vessel Steel	1577-1584
Zolnikov, K. P. / Kryzhevich, D. S. / Shilko, E. V. / Korchuganov, A. V.	Molecular Dynamics Simulation Of Electric Pulse Explosion Of Metal Wires	1421-1426
Nemoto, Yoshiki / Shibanuma, Kazuki / Suzuki, Katsuyuki / Aihara, Shuji	Monte Carlo Simulation to Predict Fracture Initiation in Mild Steel	2495-2503
Naimark, Oleg B.	More singular? Self-similar dynamics of damage localization and instability in dynamic fracture	342-349
Citarella, R. / Sepe, R. / Giannella, V. / Ishtyryakov, I.	Multiaxial Fatigue Crack Propagation of an Edge Crack in a Cylindrical Specimen Undergoing Combined Tension-Torsion Loading	2706-2717
Dmitriev, Andrey I. / Nikonov, Anton Yu. / Österle, Werner	Multiscale modeling of low friction sliding behavior of a hybrid epoxy-matrix nanocomposite	2347-2354
Yamamoto, Yuki / Shibanuma, Kazuki / Yanagimoto, Fuminori / Suzuki, Katsuyuki / Aihara, Shuji / Shirahata, Hiroyuki	Multiscale modeling to clarify the relationship between microstructures of steel and macroscopic brittle crack propagation/arrest behavior	2389-2396
Oborin, Vladimir / Sokovikov, Mikhail / Bilalov, Dmitry / Naimark, Oleg	Multiscale study of morphology of the fracture surface aluminum-magnesium alloy with consecutive dynamic and gigacycle loading	1063-1070
Gaëlle, Chretien / Christine, Sarrazin-Baudoux / Laurie, Leost / Zeline, Hervier	Near-threshold fatigue propagation of physically short and long cracks in Titanium alloy	950-957
Peschkes, Milan / Höhbusch, Jochen / Haensel, Henning / Scholten, Jan	A new approach for the analytical hcf strength assessment of components from nickel-base alloys	3202-3209
Este, Alexia / Toson, Bernard / Saliba, Jacqueline / El Yagoubi, Jalal / Mindeguia, Jean-Christophe / Martin, Eric / Morel, Stéphane	A New Approach to Simulate Interface Damage in Brittle Matrix Composites	2456-2462
Gómez, F. J. / Martín-Rengel, M. A. / Ruiz-Hervias, J. / Fathy, A. M. / Berto, F.	New iterative method to obtain the softening curve in concrete.	2841-2848
Gyímesi, Ferenc / Szigethy, András / Borbély, Venczel / Kiss, Rafael T.	New measurement possibilities of deformation anomalies and complete stress field distributions by portable digital-holographic gauge camera	2307-2314
Mirone, G. / Barbagallo, R. / Corallo, D.	A new yield criteria including the effect of lode angle and stress triaxiality	3684-3696
Bernardi, P. / Ferretti, D. / Leurini, F. / Michelini, E.	A non-linear constitutive relation for the analysis of FRCM elements	2674-2681
Sakagami, Takahide / Izumi, Yui / Shiozawa, Daiki / Fujimoto, Taisei / Mizokami, Yoshiaki / Hanai, Taku	Nondestructive Evaluation of Fatigue Cracks in Steel Bridges Based on Thermoelastic Stress Measurement	2132-2139
Bernardi, Patrizia / Cerioni, Roberto / Michelini, Elena	A nonlinear procedure for the analysis of RC beams	2873-2880
Shlyannikov, V.	Nonlinear stress intensity factors in fracture mechanics and their applications	744-752
Kontermann, C. / Almstedt, H. / Scholz, A. / Oechsner, M.	Notch Support for LCF-Loading: A Fracture Mechanics Approach	3125-3134
De Cola, F. / Pellegrino, A. / Barbieri, E. / Penumadu, D. / Petrinic, N.	A novel consolidation-based representative volume element for granular materials and its application for the characterization of the mechanical response of sand during impact loading	2905-2912
Pittarello, L. / Campagnolo, A. / Berto, F.	NSIFs estimation based on the averaged strain energy density under in-plane mixed mode loading	1829-1836
La Rosa, G. / Clienti, C. / Di Bella, S. / Rizza, F.	Numerical analysis of a custom-made pelvic prosthesis	1295-1302
Shilko, Evgeny V. / Psakhie, Sergey G. / Popov, Valentin L.	Numerical analysis of the geometrical and material criteria of acceleration of shear crack to supershear velocity in brittle nanoporous solids	409-416
Paarmann, M. / Sander, M.	Numerical examinations of different plastic material models on crack growth behaviour under elevated temperature	640-647
Rosendahl, P. L. / Weißgraeber, P. / Stein, N. / Becker, W.	A numerical finite fracture mechanics approach on asymmetric cracks in open-hole plates	1991-1998
Ren, S.-C. / Rousselier, G. / Morgeneyer, T. F. / Mazière, M. / Forest, S.	Numerical investigation of dynamic strain ageing and slant ductile fracture in a notched specimen and comparison with synchrotron tomography 3D-DVC	3385-3392
Namdar, Abdoullah	A numerical investigation on soil-concrete foundation interaction	2803-2809
Moskvichev, Egor	Numerical modeling of stress-strain behavior of composite overwrapped pressure vessel	2512-2518
Younise, Bashir / Rakin, Marko / Gubeljak, Nenad / Međo, Bojan / Sedmak, Aleksandar	Numerical prediction of ductile fracture resistance of welded joint zones	753-760
Kredegh, Abubakr / Sedmak, Aleksandar / Grbović, Aleksandar / Milosevic, Nenad / Danicic, Darko	Numerical simulation of fatigue crack growth in friction stir welded T joint made of Al 2024 T351 alloy	3065-3072
Smolin, I.Yu. / Makarov, P. V. / Eremin, M. O. / Matyko, K. S.	Numerical simulation of mesomechanical behavior of porous brittle materials	3353-3360
Bilalov, Dmitry / Sokovikov, Mikhail / Bayandin, Yuri / Chudinov, Vasiliy / Oborin, Vladimir / Naimark, Oleg	Numerical simulation of plastic strain localization and failure mode transition in metals under dynamic loading	1951-1958
Nakanishi, Daiki / Kawabata, Tomoya / Aihara, Shuji	An Observation of Brittle Crack Propagation in Coarse Grained 3% Silicon Steel	493-500
Barhli, S. M. / Saucedo-Mora, L. / Simpson, C. / Becker, T. / Mostafavi, M. / Withers, P. J. / Marrow, T. J.	Obtaining the J-integral by diffraction-based crack-field strain mapping	2519-2526
Strobl, Michael / Seelig, Thomas	On constitutive assumptions in phase field approaches to brittle fracture	3705-3712
Talemi, Reza H. / Chhith, Saosometh / De Waele, Wim	On effect of pre-bending process on low cycle fatigue behaviour of high strength steel using lock-in thermography	3135-3142
Wheel, Marcus	On energy release rates in heterogeneous composite laminates	174-181
Angelova, Donka / Yankova, Svetla / Yordanova, Rozina / Atanasova, Gergana	On monitoring mechanical characteristics of rolled electrolytic copper	2315-2322
Dashevskiy, Il’ya N.	On possibility of unloading control at leg orthotics	1277-1284
Ustinov, K. B.	On propagation of interface cracks in bi-layered strip in relation to delamination of coatings from substrates of final thickness	3439-3446
Campello, Eduardo F. / Pereira, Marcos V. / Darwish, Fathi A. / Ghavami, Khosrow	On the Fatigue Behavior of Bamboo Pulp Reinforced Cementitious Composites	2929-2935
Fortini, Annalisa / Merlin, Mattia / Fabbri, Elettra / Pirletti, Stefano / Garagnani, Gian Luca	On the influence of Mn and Mg additions on tensile properties, microstructure and quality index of the A356 aluminum foundry alloy	2238-2245
Christ, Hans-Jürgen / Wackerman, Ken / Krupp, Ulrich	On the mechanism of dynamic embrittlement and its effect on fatigue crack propagation in IN718 at 650°C	557-564
Taylor, David	On the role of microstructure in finite fracture mechanics	1999-2005
Dimakos, Konstantinos / Mariotto, Andrea / Giacosa, Fausto	Optimization Of The Fatigue Resistance Of Nitinol Stents Through Shot Peening	1522-1529
Costanza, Girolamo / Dodbiba, Gjergj / Tata, Maria Elisa	Optimization of the process parameters for the manufacturing of open-cells iron foams with high energy absorption	2277-2282
D’Agostino, L. / Di Cocco, V. / Iacoviello, F.	Overload effects on fatigue cracks in ferritic-pearlitic ductile cast irons	3369-3376
Bakic, Gordana M. / Djukic, Milos B. / Rajicic, Bratislav / Zeravcic, Vera Sijacki / Maslarevic, Aleksandar / Milosevic, Nenad	Oxidation behavior during prolonged service of boiler tubes made of 2.25Cr1Mo and 12Cr1Mo0.3V heat resistance steels	3647-3653
Chang, L. / Patel, Y. / Wang, H. / Williams, J. G.	The Partitioning of Plastic Energy in Cutting Tests	309-315
Ostapchuk, Alexey A. / Pavlov, Dmitry V.	Peculiarities of shear deformation of gouge-filled faults	2810-2817
Yolum, Uğur / Taştan, Ahmet / Güler, Mehmet A.	A Peridynamic Model for Ductile Fracture of Moderately Thick Plates	3713-3720
Larisa, Stepanova / Pavel, Roslyakov / Pavel, Lomakov	A Photoelastic Study for Multiparametric Analysis of the Near Crack Tip Stress Field Under Mixed Mode Loading	1797-1804
Ueda, Koya / Shibanuma, Kazuki / Kinefuchi, Masao / Nemoto, Yoshiki / Suzuki, Katsuyuki / Enoki, Manabu	Prediction model for fatigue life considering microstructures of steel	2575-2582
Holmen, J. K. / Dæhli, L. E. B. / Hopperstad, O. S. / Børvik, T.	Prediction of ductile failure using a phenomenological model calibrated from micromechanical simulations	2543-2549
Coppola, T. / Iob, F. / Cortese, L. / Campanelli, F.	Prediction of ductile fracture in anisotropic steels for pipeline applications	2936-2943
Hwu, Chyanbin / Yeh, Yu-Kuei	Prediction of fracture toughness for carbon nanotubes	1327-1334
Smolin, A. Yu. / Smolin, I. Yu. / Smolina, I. Yu.	Probabilistic Approach for Analysis of Strength of Ceramics With Different Porous Structure Based on Movable Cellular Automaton Modeling	2742-2749
Ramos, Alberto / Muniz-Calvente, Miguel / Lamela-Rey, María Jesús / Fernández, Pelayo / Fernández-Canteli, Alfonso	Probabilistic failure analysis for glass components under general loading conditions	2591-2597
Jallouf, S. / Pluvinage, G. / Casavola, K. / Pappalettere, C.	A Probabilistic Fatigue Assessment Diagram To Get A Guaranteed Lifetime With A Low Probability Of Failure	2447-2455
Konstantinović, M. J.	Probabilistic fracture mechanics of irradiation assisted stress corrosion cracking in stainless steels	3792-3798
Nakagawa, Akiyoshi / Sakai, Tatsuo / Harlow, D. Gary / Oguma, Noriyasu / Nakamura, Yuki / Ueno, Akira / Kikuchi, Shoichi / Sakaida, Akiyoshi	A probabilistic model on crack initiation modes of metallic materials in very high cycle fatigue	1199-1206
Dakanali, I. / Stavrakas, I. / Triantis, D. / Kourkoulis, S. K.	Pull-out of threaded reinforcing bars from marble blocks	2865-2872
Schrittesser, B. / Pinter, G. / Schwarz, Th. / Kadar, Z. / Nagy, T.	Rapid Gas Decompression Performance of elastomers – A study of influencing testing parameters	1746-1754
Rajpurohit, R. S. / Santhi Srinivas, N. C. / Singh, Vakil	Ratcheting Strain Accumulation Due to Asymmetric Cyclic Loading of Zircaloy-2 at Room Temperature	2757-2763
Krepl, Ondrej / Klusak, Jan	Reconstruction of a 2D stress field around the tip of a sharp material inclusion	1920-1927
Restuccia, Luciana / Spoto, Consuelo / Ferro, Giuseppe Andrea / Tulliani, Jean-Marc	Recycled Mortars with C&D Waste	2896-2904
Ferro, P. / Berto, F. / James, M. N. / Borsato, T.	Review of recent advances in local approaches applied to pre-stressed components under fatigue loading	3467-3474
Sedmak, Aleksandar / Kirin, Snežana / Golubovic, Tamara / Mitrović, Slobodan / Stanojevic, Petar	Risk Based Approach to Integrity Assessment of a Large Spherical Pressure Vessel	3654-3659
Smolin, A. Yu. / Eremina, G. M. / Shilko, E. V. / Psakhie, S. G.	Role of vortex-like motion in fracture of coating-substrate system under contact loading	1781-1788
Di, Yidu / Novokshanov, Denis / Münstermann, Sebastian	Safety assessment of steels under ULCF loading conditions with damage mechanics model	632-639
Davydova, Marina / Uvarov, Sergey	Scaling laws of structure and fragmentation parameters of ZrO2 ceramics.	1936-1943
Darvishi, Ershad / Namdar, Abdoullah / Feng, Xiong / Ge, Qi	Seismic resistance of timber structure - a state of the art design	2750-2756
Torabian, Noushin / Favier, Véronique / Ziaei-Rad, Saeed / Adamski, Frédéric / Dirrenberger, Justin / Ranc, Nicolas	Self-Heating Measurements for a Dual-Phase Steel under Ultrasonic Fatigue Loading for stress amplitudes below the conventional fatigue limit	1191-1198
Spagnoli, A. / Terzano, M. / Klarbing, A. / Barber, J. R.	Shakedown in an elastic-plastic solid with a frictional crack	2667-2673
Meshcheryakov, Yurii / Divakov, Alexandre / Zhigacheva, Natali / Konovalov, Grigorii	Shock-induced structural instability and dynamic strength of brittle solids	477-484
Divakov, Alexandre / Meshcheryakov, Yurii / Silnikov, N. M.	Shock-induced structural instability and dynamic strength of metals	460-467
Abecassis, Manon / Köster, Alain / Maurel, Vincent	Short and long crack growth behavior of welded ferritic stainless steel	3515-3522
Farahani, Behzad V. / Tavares, Paulo J. / Moreira, P. M. G. P.	SIF Determination with Thermoelastic Stress Analysis	2148-2155
Yixiu, Shu / Yazhi, Li	A Simple and Efficient X-FEM Approach for Non-planar Fatigue Crack Propagation	2550-2557
Kim, Sang-Hyun / Gim, Jae-Min / Miao, Wang / Kim, Yun-Jae	Simplified limit load estimation using mα-tangent method for branch pipe junctions under internal pressure and in-plane bending	2583-2590
Bailey, P. B. S.	Sources of Variation in JIC Measurements of Ductile Fracture Toughness Using Unloading Compliance	3758-3763
Šmíd, Miroslav / Hutař, Pavel / Horník, Vít / Hrbáček, Karel / Kunz, Ludvík	Stage I fatigue cracking in MAR-M 247 superalloy at elevated temperatures	3018-3025
Mirone, G. / Barbagallo, R. / Corallo, D. / Di Bella, S.	Static and dynamic response of titanium alloy produced by electron beam melting	2355-2366
Burago, N. G. / Nikitin, A. D. / Nikitin, I. S. / Yushkovsky, P. A.	Stationary vibrations and fatigue failure of compressor disks of variable thickness	1109-1116
Mitrovic, Radivoje M. / Miskovic, Zarko Z. / Djukic, Milos B. / Bakic, Gordana M.	Statistical correlation between vibration characteristics, surface temperatures and service life of rolling bearings – artificially contaminated by open pit coal mine debris particles	2338-2346
Colussi, Marco / Berto, Filippo / Mori, Kotaro / Narita, Fumio	Strain Energy Density Based Assessment of Cracked Terfenol-D Specimens Under Magnetic Field and Different Loading Rates	1837-1844
Evstifeev, A. / Petrov, Y. / Bragov, A. / Konstantinov, A.	The strength competition effect at different strain rates	446-451
Dimaki, Andrey V. / Shilko, Evgeny V. / Psakhie, Sergey G.	Strength of water-filled permeable elastic-plastic medium under shear accompanied by compression: A theoretical study	2606-2613
Zvirko, O. I. / Savula, S. F. / Tsependa, V. M. / Gabetta, G. / Nykyforchyn, H. M.	Stress corrosion cracking of gas pipeline steels of different strength	509-516
Leon, Lee / Charles, Raymond / Simpson, Nicola	Stress-strain behaviour of asphalt concrete in compression	2913-2920
Tyutin, M. R. / Botvina, L. R. / Levin, V. P. / Petersen, T. B. / Demina, Yu. A. / Soldatenkov, A. P. / Demin, A. I.	Structural and physical criteria of ultimate state of material before fracture	2764-2771
Jazaeri, H. / Bouchard, P. J. / Hutchings, M. T. / Mamun, A. A. / Heenan, R. K.	Study of cavities in a creep crack growth test specimen	942-949
Plekhov, O. / Naimark, O. / Narykova, M. / Kadomtsev, A. / Betechtin, V.	Study of Dissipation Properties and Structure Evolution in Metals with Different Grain Size under HCF and VHCF Loadings	2084-2090
Islam, Md. Shafiqul / Zhang, Defeng / Mehmood, Nasir / Kao-Walter, Sharon	Study of Shear Dominant Delamination in Thin Brittle-High Ductile Interface	152-157
Šarac, T. / Quiévy, N. / Gusarov, A. / Konstantinović, M. J.	The study of temperature and radiation induced degradation of cable polymers: A comparison between the mechanical properties of industrial and neat EPDM	2405-2414
Dehmani, Helmi / Brugger, Charles / Palin-Luc, Thierry / Mareau, Charles / Koechlin, Samuel	Study of the contribution of different effects induced by the punching process on the high cycle fatigue strength of the M330-35A electrical steel	3256-3263
Sanz, Beatriz / Planas, Jaime / Sancho, José M.	Study of the influence of the oxide and concrete parameters on the results of accelerated corrosion tests	2849-2856
Ancona, F. / De Finis, R. / Demelio, G. P. / Galietti, U. / Palumbo, D.	Study of the plastic behavior around the crack tip by means of thermal methods	2113-2122
Ueno, A. / Takane, T. / Ueno, F.	Study on degradation of electrolyte membrane for PEFC	2323-2329
Yamada, Takehisa / Yamashita, Yoichi / Kanna, Sohei	A study on evaluation of ductile crack initiation using strain hardening exponent for steels	2206-2213
Jie, Su / Yazhi, Li / Wei, Jiang / Dailong, Zhang	Study on microscopic ductile fracture of in-situ TiB2/2024 Al matrix composite	2222-2229
Wallin, Kim / Karjalainen-Roikonen, Päivi / Suikkanen, Pasi	Sub-sized CVN specimen conversion methodology	3735-3742
Chail, Guocai / Kangas, Pasi	Super and hyper duplex stainless steels: structures, properties and applications	1755-1762
Shlyannikov, V. / Zakharov, A. / Lyagova, A.	Surface and through thickness crack growth in cruciform specimens subjected to biaxial loading	3248-3255
Kazarinov, N. / Evsyifeev, A. / Petrov, Y. / Lashkov, V. / Atroshenko, S. / Valiev, R.	Surface roughness investigation of ultrafine-grained aluminum alloy subjected to high speed erosion	485-492
Berto, Filippo / Campagnolo, Alberto / Meneghetti, Giovanni / Tanaka, Keisuke	Synthesis of crack initiation life in steel notched specimens under torsional fatigue based on the averaged strain energy density	1853-1860
Lindqvist, Sebastian	Tearing resistance of heterogeneous interface region of a dissimilar metal weld characterised with sub-sized single edge bend specimens	1031-1038
Knitel, S. / Spätig, P. / Seifert, H. P.	Temperature and Loading-Rate Dependence on a Local Criterion for Cleavage Fracture in the Transition Region of the Tempered Martensitic Steel Eurofer97.	1684-1691
Achchaq, Fouzia / Jomaa, Wahbi / Godin, Alexandre / Bontemps, Stéphanie / Puiggali, Jean-Rodolphe	Temperature and moisture effects on the failure mode of highly shrinkable raw catalyst supports	2283-2290
Tsuchiya, Toshiyuki / Hemmi, Tetsuya / Suzuki, Jun-ya / Hirai, Yoshikazu / Tabata, Osamu	Tensile fracture of integrated single-crystal silicon nanowire using MEMS electrostatic testing device	1405-1412
Alexopoulos, Nikolaos D. / Examilioti, Theano N. / Stergiou, Vasilis / Kourkoulis, Stavros K.	Tensile mechanical performance of electron-beam welded joints from aluminum alloy (Al-Mg-Si) 6156	3539-3545
Horikawa, Noriyo / Kawano, Yuki / Miyajima, Toshiro / Nomura, Yukihiro / Kitagawa, Tooru / Ueno, Akira / Sakaida, Akiyoshi / Mori, Takao	Tensile Strength of Poly-p- Phenylene Benzobisoxazole (PBO) Fiber with Kinking Damage	293-300
Szachogluchowicz, I. / Sniezek, L. / Sulym, H. / Gloc, M.	Testing and verification modeling of wave-shape formation under explosion welding to laminate AA 2519-Ti6Al4V	2375-2380
Crupi, V. / Guglielmino, E. / Plekhov, O. / Prokhorov, A. / Risitano, G.	Theoretical Approach for Developing the Thermographic Method in Ultrasonic Fatigue	1221-1228
Astafurov, S. V. / Shilko, E. V. / Grigoriev, A. S. / Ovcharenko, V. E. / Psakhie, S. G.	Theoretical investigation of influence of peculiarities of internal structure on deformation and fracture of metal-ceramic composites using discrete element approach	2214-2221
Pelekis, Iason / Susmel, Luca	The Theory of Critical Distances to estimate static and dynamic strength of notched plain concrete	2006-2013
Ferro, P. / Berto, F. / Borsato, T.	Thermal load-induced notch stress intensity factors derived from averaged strain energy density	2367-2374
Seddik, R. / Seddik, M. / Atig, A. / Fathallah, R.	Thermo-mechanical relaxation of compressive residual stresses induced by shot peening	2182-2189
Urbanek, Ralf / Bär, Jürgen	Thermographic Image Analysis of Fatigue Crack Propagation in a High-Alloyed Steel under usage of discrete fourier transformation and rigid body motion compensation	2097-2104
Longkui, Zhu / Zhengcao, Li / Lijie, Qiao	A three-dimensional model of non-slipping stress corrosion cracking under low loads	612-621
Hörrmann, Susanne / Adumitroaie, Adi / Schagerl, Martin	Through-thickness fatigue behavior of non-crimp fabrics featuring manufacturing defects	158-165
Pini, Tommaso / Briatico-Vangosa, Francesco / Frassine, Roberto / Rink, Marta	Time dependent fracture behaviour of a carbon fibre composite based on a (rubber toughened) acrylic polymer	253-260
Stanzl-Tschegg, Stefanie E.	Time Saving Method for Measuring VHC Fatigue and Fatigue Crack Growth Data with the Ultrasonic Fatigue Technique	3-10
Bajpai, Ankur / Alapati, Arun Kumar / Wetzel, Bernd	Toughening and Mechanical Properties of Epoxy Modified with Block Co-polymers and MWCNTs	104-111
Djukic, Milos B. / Bakic, Gordana M. / Zeravcic, Vera Sijacki / Rajicic, Bratislav / Sedmak, Aleksandar / Mitrovic, Radivoje / Mišković, Žarko	Towards a unified and practical industrial model for prediction of hydrogen embrittlement and damage in steels	604-611
Bannikova, Irina A. / Naimark, Oleg B. / Uvarov, Sergey V.	Transition from multi-center fracture to fragmentation statistics under intensive loading	1944-1950
Planas, Jaime / Sanz, Beatriz / Sancho, José M.	Transition from smeared to localized cracking in macro-defect-free quasibrittle structures	3676-3683
Kashtalyan, Maria / Piat, Romana / Guz, Igor	Transverse cracking in metal/ceramic composites with lamellar microstructure	3377-3384
Meneghetti, G. / Terrin, A. / Giacometti, S.	A twin disc test rig for contact fatigue characterization of gear materials	3185-3193
Zahedi, S. Abolfazl / Jivkov, Andrey	Two-parameter fracture characterization of a welded pipe in the presence of residual stresses	777-784
Esposito, L.	Type IV creep cracking of welded joints: numerical study of the grain size effect in HAZ	919-926
Fitzka, M. / Catoor, D. / Irrasch, D. / Reiterer, M. / Mayer, H.	Ultrasonic fatigue testing of thin MP35N alloy wire	1039-1046
Tesei, Claudia / Ventura, Giulio	A unilateral nonlocal tensile damage model for masonry structures	2690-2697
Dæhli, L. E. B. / Faleskog, J. / Børvik, T. / Hopperstada, O. S.	Unit cell simulations and porous plasticity modelling for recrystallization textures in aluminium alloys	2535-2542
Merson, E. / Kudrya, A. V. / Trachenko, V. A. / Merson, D. / Danilov, V. / Vinogradov, A.	The Use of Confocal Laser Scanning Microscopy for the 3D Quantitative Characterization of Fracture Surfaces and Cleavage Facets.	533-540
La Rosa, G. / Clienti, C. / Cugno Garrano, A. Marino	The use of Digital Image Correlation to correct the thermoelastic curves in static tests	2140-2147
Han, J.-J. / Larrosa, N. O. / Ainsworth, R. A. / Kim, Y.-J.	The use of SE(T) specimen fracture toughness for FFS assessment of defects in low constraint conditions	1724-1737
Gallo, Pasquale / Berto, Filippo / Glinka, Gregory	V-notched components under non-localized creeping condition: numerical evaluation of stresses and strains	809-816
Lei, Yuebao	Validation of contour integral functions (J and C(t)) in ABAQUS v6.11-v6.14 for combined mechanical and residual stresses	2566-2574
Berg, Joern / Stranghoener, Natalie / Kern, Andreas / Hoevel, Marion	Variable amplitude fatigue tests at high frequency hammer peened welded ultra high strength steel S1100	3554-3561
Tang, K. K. / Berto, F. / Wu, H.	Variation of transitional functions in multiscale fatigue crack growth of superalloys	1878-1885
Sander, Manuela / Müller, Thomas / Stäcker, Carsten	Very high cycle fatigue behavior under constant and variable amplitude loading	34-41
Waqas Tofique, Muhammad / Bergström, Jens / Burman, Christer	Very high cycle fatigue crack initiation mechanisms in different engineering alloys	1181-1190
Spriestersbach, D. / Brodyanski, A. / Lösch, J. / Kopnarski, M. / Kerscher, E.	Very high cycle fatigue of high-strength steels: Crack initiation by FGA formation investigated at artificial defects	1101-1108
Karr, U. / Stich, A. / Mayer, H.	Very high cycle fatigue of wrought magnesium alloy AZ61	1047-1054
Lang, K.-H. / Korn, M. / Rohm, T.	Very High Cycle Fatigue Resistance of the Low Alloyed Steel 42CrMo4 in Medium- and High-Strength Quenched and Tempered Condition	1133-1142
Tridello, A. / Paolino, D. S. / Chiandussi, G. / Rossetto, M.	VHCF strength decrement in large H13 steel specimens subjected to ESR process	1117-1124
Student, Oleksandra / Krechkovs’ka, Halyna	Visualization of Damages of the Main Pipelines Using Cyclic Hydro Testing	549-556
Sathuvalli, Udaya B. / Rahman, Shaikh / Wooten, James / Suryanarayana, P. V.	Wear efficiency of oil-well casings exposed to rotating tooljoints	1771-1780
Morgado, T. L. M. / Navas, H. / Brites, R.	Wear study of Innovative Ti-Ta alloys	1266-1276
Seal, C. K. / Sherry, A. H.	Weibull distribution of brittle failures in the transition region	1668-1675
Costanza, Girolamo / Sili, Andrea / Tata, Maria Elisa	Weldability of austenitic stainless steel by metal arc welding with different shielding gas	3508-3514
Shimada, Y. / Shimanuki, H. / Igi, S. / Minami, F.	WES 2808 for Brittle Fracture Assessment of Steel Components Under Seismic Conditions Part II: Change in Mechanical Properties of Structural Steels by Pre-strain and Dynamic Loading	1593-1600
Igi, Satoshi / Shimada, Yusuke / Kinefuchi, Masao / Minami, Fumiyoshi	WES 2808 for brittle fracture assessment of steel components under seismic conditions Part III: Change in CTOD fracture toughness of structural steels by pre-strain and dynamic loading	1601-1609
Yamaguchi, T. / Kinefuchi, M. / Igi, S. / Shimada, Y. / Takashima, Y. / Minami, F.	WES 2808 for brittle fracture assessment of steel components under seismic conditions Part-IV: Change in mechanical properties and fracture toughness of steel weld HAZ by pre-strain	1627-1634
Minami, F. / Ohata, M. / Takashima, Y. / Shimanuki, H. / Shimada, Y. / Suzuki, T. / Igi, S. / Ishii, T. / Kinefuchi, M. / Yamaguchi, T. / Nakagomi, T. / Hagihara, Y.	WES 2808 for Brittle Fracture Assessment of Steel Components under Seismic Conditions – Part I: Fracture Assessment Procedure	1561-1568
Ohata, Mitsuru / Takashima, Yasuhito / Minami, Fumiyoshi	WES 2808 for Brittle Fracture Assessment of Steel Components under Seismic Conditions – Part V: Equivalent CTOD ratio for correction of constraint loss in beam-to-column connections	1635-1642
Takashima, Y. / Ohata, M. / Ishii, T. / Hagihara, Y. / Minami, F.	WES 2808 for Brittle Fracture Assessment of Steel Components under Seismic Conditions – Part VI: Application of WES 2808 to Beam-to-column Connections	1585-1592
Sacchetti, F. / Grouve, W. J. B. / Warnet, L. L. / Villegas, I. Fernandez	Woven fabric composites: Can we peel it?	245-252
Mukai, Yasuhiro	X-ray diffraction study on inelastic deformation behavior of Ni-base single crystal superalloy	895-902

Informations
sur cette fiche
IssueID
60049
Publié(e) le:
04.12.2021
Modifié(e) le:
09.05.2022

Publicité

Structurae coopère avec

International Association for Bridge and Structural Engineering (IABSE)

Publicité

Procedia Structural Integrity - 2016

Articles dans ce numéro

Vous avez dépassé votre limite de téléchargement mensuelle !

Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois.
Les utilisateurs·rices de Structurae Pro sont limités à 50.

Données obligatoires

Procedia Structural Integrity - 2016

Articles dans ce numéro

Vous avez dépassé votre limite de téléchargement mensuelle ! Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois. Les utilisateurs·rices de Structurae Pro sont limités à 50.

Données obligatoires

Vous avez dépassé votre limite de téléchargement mensuelle !

Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois.
Les utilisateurs·rices de Structurae Pro sont limités à 50.