Binrong Zhu
- (2024): Full-scale experiment and FEA simulation on failure mechanism of the cross-arm of a UHV strain transmission tower in icing areas. In: Structures, v. 69 (November 2024).
- (2024): Influence of waste glass powder on printability and mechanical properties of 3D printing geopolymer concrete. In: Developments in the Built Environment, v. 20 (December 2024).
- (2024): Assessment of the properties of interface-modified bamboo aggregates for sustainable concrete construction. In: Journal of Building Engineering, v. 94 (October 2024).
- (2024): Physical and mechanical properties of sustainable bamboo coarse aggregate concrete. In: Construction and Building Materials, v. 431 (June 2024).
- (2024): Solid waste-based low-carbon autoclaved aerated concrete: Relationship between engineering properties and microstructure. In: Journal of Building Engineering, v. 91 (August 2024).
- (2023): The Bearing Capacity of Composite Insulated Cross Arm Tower under Typhoon Load. In: Journal of Physics: Conference Series, v. 2541, n. 1 (1 July 2023).
- (2021): Research on the material properties of corroded angle steel members of the in-service transmission tower. In: IOP Conference Series: Earth and Environmental Science, v. 825, n. 1 (1 July 2021).
- (2024): Enhancing mechanical performance and durability of high strength mortar with incineration bottom ash via Al2O3 micro-powder: An experimental study. In: Journal of Building Engineering, v. 89 (July 2024).
- (2024): Development of a novel extrusion device to improve the printability of 3D printable geopolymer concrete. In: Journal of Building Engineering, v. 88 (July 2024).
- (2024): Mechanical properties and stress-strain relationship of surface-treated bamboo fiber reinforced lightweight aggregate concrete. In: Construction and Building Materials, v. 424 (April 2024).
- (2024): Experimental study on the basic properties of new biomass bamboo aggregate concrete. In: Journal of Building Engineering, v. 86 (June 2024).
- (2023): Investigation of the rheological and mechanical properties of 3D printed eco-friendly concrete with steel slag. In: Journal of Building Engineering, v. 72 (August 2023).
- (2023): An experimental study on the influence of waste rubber particles on the compressive, flexural and impact properties of 3D printable sustainable cementitious composites. In: Case Studies in Construction Materials, v. 19 (December 2023).
- (2023): Improving mechanical properties of 3D printable ‘one-part’ geopolymer concrete with steel fiber reinforcement. In: Journal of Building Engineering, v. 75 (September 2023).
- (2013): Assessment on the stress state and the maintenance schemes of the transmission tower above goaf of coal mine. In: Engineering Failure Analysis, v. 31 (July 2013).
- (2021): Mechanical properties of engineered cementitious composites beams fabricated by extrusion-based 3D printing. In: Engineering Structures, v. 238 (July 2021).
- (2017): Accelerated life testing of concrete based on stochastic approach and assessment. In: Computers and Concrete, v. 19, n. 1 (January 2017).
- (2016): Wind tunnel tests on wind loads acting on an angled steel triangular transmission tower. In: Journal of Wind Engineering and Industrial Aerodynamics, v. 156 (September 2016).
- (2018): Experimental Study of Competing Failure of Reinforced Concrete Based on the Weibull Distribution. In: Advances in Civil Engineering Materials, v. 7, n. 1 (December 2018).
- (2018): Accelerated Life Testing of Reinforced Concrete Based on Performance Degradation and Reliability Modeling. In: Journal of Materials in Civil Engineering (ASCE), v. 30, n. 5 (May 2018).
- (2018): Theoretical model for the bond-slip relationship between ribbed steel bars and confined concrete. In: Structural Concrete, v. 19, n. 2 (April 2018).
- (2017): Basic parameters test and 3D modeling of bond between high-strength concrete and ribbed steel bar after elevated temperatures. In: Structural Concrete, v. 18, n. 5 (October 2017).
- (2018): The Numerical analysis and full-scale experiment on K-joint deformations in the crank arms of lattice transmission towers. In: The Structural Design of Tall and Special Buildings, v. 27, n. 5 (10 April 2018).
Structurae cooperates with
