Tatheer Zahra 
- (2024): Advancement in Sustainable 3D Concrete Printing: A Review on Materials, Challenges, and Current Progress in Australia. In: Buildings, v. 14, n. 2 (1 February 2024).
- (2024): Cyclic in-plane shear behaviour of reinforced concrete masonry walls with single and double layered reinforcement. In: Construction and Building Materials, v. 421 (March 2024).
- (2024): Flexural behaviour of cementitious composites embedded with 3D printed re-entrant chiral auxetic meshes. In: Smart Materials and Structures, v. 33, n. 2 (4 January 2024).
- (2023): Enhanced energy absorption of auxetic cementitious composites with polyurethane foam layers for building protection application. In: Journal of Building Engineering, v. 78 (November 2023).
- (2024): Out of-plane failure analysis of masonry walls subjected to hydrostatic and hydrodynamic loads induced by flash floods. In: Engineering Structures, v. 298 (January 2024).
- (2023): Behaviour of reinforced mortarless concrete masonry panels under axial compression: An experimental and analytical study. In: Construction and Building Materials, v. 377 (May 2023).
- (2023): In-plane and out-of-plane shear characteristics of reinforced mortarless concrete block masonry. In: Journal of Building Engineering, v. 66 (May 2023).
- (2023): Behaviour and material properties of versaloc semi-interlocking mortarless masonry. In: Materials and Structures, v. 56, n. 1 (30 January 2023).
- (2021): Experimental investigation on the effectiveness of lateral restrainers to the vertical steel in reinforced masonry walls under axial compression. In: Construction and Building Materials, v. 297 (August 2021).
- (2022): Analytical model for CFRP confined masonry columns subjected to monotonic and cyclic compression. In: Composite Structures, v. 292 (July 2022).
- (2022): Innovative impact testing machine for enhancing impact related research in Australia. In: International Journal of Protective Structures, v. 13, n. 2 (April 2022).
- (2022): Finite element modelling of reinforced masonry walls under axial compression. In: Engineering Structures, v. 252 (February 2022).
- (2022): Influence of restrainer bar chairs on the compression and flexural behaviour of reinforced masonry walls. In: Structures, v. 35 (January 2022).
- (2021): Improved design provisions for reinforced concrete block masonry walls under axial compression. In: Construction and Building Materials, v. 310 (December 2021).
- (2021): Geometrically modified auxetic polyurethane foams and their potential application in impact mitigation of masonry structures. In: Construction and Building Materials, v. 311 (December 2021).
- (2021): Behaviour of 3D Printed Re-entrant Chiral Auxetic (RCA) Geometries under In-Plane and Out-of-Plane Loadings. In: Smart Materials and Structures, v. 30, n. 11 (24 September 2021).
- (2021): Analytical stress–strain model of reinforced concrete masonry wallettes under axial compression. In: Structures, v. 34 (December 2021).
- (2022): Influence of blockaid chairs on compression and amp out-of-plane behaviour of reinforced masonry walls. In: Australian Journal of Civil Engineering, v. 20, n. 2 (January 2022).
- (2021): Assessing vibration induced damage in unreinforced masonry walls subject to vehicular impact – A numerical study. In: Engineering Structures, v. 245 (October 2021).
- (2021): Monotonic and cyclic compression characteristics of CFRP confined masonry columns. In: Composite Structures, v. 272 (September 2021).
- (2021): Failure of masonry walls under high velocity impact – A numerical study. In: Engineering Structures, v. 238 (July 2021).
- (2021): Effect of geometry on the compression characteristics of bonded brickwork. In: Structures, v. 32 (August 2021).
- (2014): Condition assessment and strengthening of residential units. In: Case Studies in Construction Materials, v. 1 ( 2014).
- (2021): Compressive strength and deformation characteristics of concrete block masonry made with different mortars, blocks and mortar beddings types. In: Journal of Building Engineering, v. 38 (June 2021).
- (2020): Impact mitigation of masonry walls with carbon fibre and Auxetic fibre composite renders – A numerical study. In: Structures, v. 28 (December 2020).
- (2020): Interfacial transition zone modelling for characterisation of masonry under biaxial stresses. In: Construction and Building Materials, v. 249 (July 2020).
- (2018): Characterisation and strategies for mitigation of the contact surface unevenness in dry-stack masonry. In: Construction and Building Materials, v. 169 (April 2018).
- (2020): Development of design methodology for mortarless masonry system: Case study – a resettlement housing colony. In: Journal of Building Engineering, v. 27 (January 2020).
- (2019): Characterisation of polymer cement mortar composites containing carbon fibre or auxetic fabric overlays and inserts under flexure. In: Construction and Building Materials, v. 224 (November 2019).
- (2017): Characterisation of cementitious polymer mortar – Auxetic foam composites. In: Construction and Building Materials, v. 147 (August 2017).
Structurae cooperates with
