Nassim Sebaibi 
- (2024): Enhancing Energy Efficiency in Moroccan Construction through Innovative Materials: A Case Study in a Semiarid Climate. In: Buildings, v. 14, n. 10 (8 October 2024).
- (2024): Influence of the Mass Percentage of Bottom Ash and Its State of Maturation on the Mechanical Performance of a Bio-Composite. In: Buildings, v. 14, n. 8 (23 July 2024).
- (2023): Review of Advances in 3D Printing Technology of Cementitious Materials: Key Printing Parameters and Properties Characterization. In: Buildings, v. 13, n. 7 (28 June 2023).
- (2023): Monitoring of drying kinetics evolution and hygrothermal properties of new earth-based materials using climatic chamber simulation. In: Case Studies in Construction Materials, v. 18 (July 2023).
- (2023): Effect of latent heat storage on thermal comfort and energy consumption in lightweight earth-based housings. In: Building and Environment, v. 229 (February 2023).
- (2023): Artificial reefs built by 3D printing: Systematisation in the design, material selection and fabrication. In: Construction and Building Materials, v. 362 (January 2023).
- (2022): Fatigue behavior of concrete: A literature review on the main relevant parameters. In: Construction and Building Materials, v. 338 (July 2022).
- (2022): Valorization of queen scallop shells in the preparation of metakaolin-based geopolymer mortars. In: Journal of Building Engineering, v. 53 (August 2022).
- (2022): Improvement of cob thermal inertia by latent heat storage and its implication on energy consumption. In: Construction and Building Materials, v. 329 (April 2022).
- (2022): Earth construction: Field variabilities and laboratory reproducibility. In: Construction and Building Materials, v. 314 (January 2022).
- (2021): Impact of phase change materials on lightened earth hygroscopic, thermal and mechanical properties. In: Journal of Building Engineering, v. 41 (September 2021).
- (2021): Evaluation of the influence of accelerated carbonation on the microstructure and mechanical characteristics of coconut fibre-reinforced cementitious matrix. In: Journal of Building Engineering, v. 39 (July 2021).
- (2021): Optimisation of 3D printed concrete for artificial reefs: Biofouling and mechanical analysis. In: Construction and Building Materials, v. 272 (February 2021).
- (2020): Optimization of non-autoclaved aerated insulating foam using bio-based materials. In: Construction and Building Materials, v. 262 (November 2020).
- (2020): Reducing energy consumption of prefabricated building elements and lowering the environmental impact of concrete. In: Engineering Structures, v. 213 (June 2020).
- (2020): Recycled duvets for building thermal insulation. In: Journal of Building Engineering, v. 31 (September 2020).
- (2019): Effect of several parameters on non-autoclaved aerated concrete: use of recycling waste perlite. In: European Journal of Environmental and Civil Engineering, v. 26, n. 1 (October 2019).
- (2012): Mechanical properties of concrete-reinforced fibres and powders with crushed thermoset composites: The influence of fibre/matrix interaction. In: Construction and Building Materials, v. 29 (April 2012).
- (2012): Mechanical and physical properties of a cement matrix through the recycling of thermoset composites. In: Construction and Building Materials, v. 34 (September 2012).
- (2012): Waste fibre–cement matrix bond characteristics improved by using silane-treated fibres. In: Construction and Building Materials, v. 37 (December 2012).
- (2013): Composition of self compacting concrete (SCC) using the compressible packing model, the Chinese method and the European standard. In: Construction and Building Materials, v. 43 (June 2013).
- (2013): Valorization of seashell by-products in pervious concrete pavers. In: Construction and Building Materials, v. 49 (December 2013).
- (2014): Experimental and numerical study of the structural and cracking behavior of an overlaid slab panel under cyclic flexural loading. In: Construction and Building Materials, v. 52 (February 2014).
- (2014): Influence of the distribution and orientation of fibres in a reinforced concrete with waste fibres and powders. In: Construction and Building Materials, v. 65 (August 2014).
- (2014): A modified method for the design of pervious concrete mix. In: Construction and Building Materials, v. 73 (December 2014).
- (2017): A bibliography on the analytical model of the mechanical behaviour in uniaxial tension of fibre concrete: Application to concrete reinforced with fibres and powders from recycling of thermoset composite materials. In: Construction and Building Materials, v. 131 (January 2017).
- (2017): Durability of pervious concrete using crushed seashells. In: Construction and Building Materials, v. 135 (March 2017).
- (2019): Mechanical performance of a dry mortar without cement, based on paper fly ash and blast furnace slag. In: Journal of Building Engineering, v. 22 (March 2019).
- (2016): Properties of ordinary concretes incorporating crushed queen scallop shells. In: Materials and Structures, v. 49, n. 5 (May 2016).
Structurae cooperates with
