Xiaoqian Qian 
- (2024): Recycling stone powder as a partial substitute for cementitious materials into eco-friendly manufactured sand ultra-high performance concretes: Towards cleaner and more cost-effective construction production. In: Journal of Building Engineering, v. 92 (September 2024).
- (2024): Identification of indexes that could reflect early drying shrinkage of high strength concrete with minerals. In: Construction and Building Materials, v. 420 (March 2024).
- (2023): Early-age shrinkage behavior of cement-fly ash paste under wind speeds: A study using BSE-IA and MIP techniques. In: Construction and Building Materials, v. 402 (October 2023).
- (2023): Effects of kaolin-modified superabsorbent polymers on mortar properties. In: Journal of Building Engineering, v. 79 (November 2023).
- (2024): Utilization of solid waste from tunnel excavation as manufactured sand with different lithology and pre-washing process for preparation of eco-friendly ultra-high performance concretes: Properties and microstructural analysis. In: Journal of Building Engineering, v. 82 (April 2024).
- (2023): Properties and microstructures of 3D printable sulphoaluminate cement concrete containing industrial by-products and nano clay. In: Journal of Building Engineering, v. 73 (August 2023).
- (2023): Powder gradation effect on the fresh, mechanical, and early-age shrinkage properties of UHPC. In: Journal of Building Engineering, v. 67 (May 2023).
- (2022): Application potential of granite cutting waste and tunnel excavation rock as fine aggregates in cement-based materials based on surface characteristics. In: Journal of Building Engineering, v. 62 (December 2022).
- (2023): Synthesis and characterization of a new super absorbent polymer (SAP) via the use of low-grade kaolin through inverse suspension polymerization. In: Construction and Building Materials, v. 363 (January 2023).
- (2022): Size distribution of pores and their geometric analysis in red mud-based autoclaved aerated concrete (AAC) using regression neural network and elastic mechanics. In: Construction and Building Materials, v. 359 (December 2022).
- (2022): Effects of red mud on workability and mechanical properties of autoclaved aerated concrete (AAC). In: Journal of Building Engineering, v. 61 (December 2022).
- (2022): Performances of UHPC bonded cementitious composite systems containing styrene-butadiene rubber latex in a chloride-rich environment. In: Construction and Building Materials, v. 353 (October 2022).
- (2022): Investigation of early drying shrinkage of ultrahigh-performance concrete under windy conditions. In: Journal of Building Engineering, v. 57 (October 2022).
- (2022): Is early drying shrinkage still determined by the mesopore content? A case study of cement paste with minerals. In: Journal of Building Engineering, v. 50 (June 2022).
- (2022): Effect of different strengthening materials on tensile behaviour of plasters and renders. In: Journal of Building Engineering, v. 56 (September 2022).
- (2022): Performance buildup of concrete cured under low-temperatures: Use of a new nanocomposite accelerator and its application. In: Construction and Building Materials, v. 335 (June 2022).
- (2022): Characterization of historical mortar from ancient city walls of Xindeng in Fuyang, China. In: Construction and Building Materials, v. 315 (January 2022).
- (2020): The influence of Si/Al ratio on sulfate durability of metakaolin-based geopolymer. In: Construction and Building Materials, v. 265 (December 2020).
- (2020): Effect of different wind speeds and sealed curing time on early-age shrinkage of cement paste. In: Construction and Building Materials, v. 255 (September 2020).
- (2019): Influence of evaporation rate on pore size distribution, water loss, and early-age drying shrinkage of cement paste after the initial setting. In: Construction and Building Materials, v. 226 (November 2019).
- (2012): Effect of nano-TiO2 on the mechanical properties of cement mortar. In: Construction and Building Materials, v. 29 (April 2012).
- (2012): Development and design of composite cementitious material at long-time circular elevated temperature in metallurgy environment. In: Construction and Building Materials, v. 35 (October 2012).
Structurae cooperates with
