Laibo Li
- (2025): In-situ growth of AFt in early induction stage to generate 3D network with C-S-H for Portland cement crack resistance. In: Construction and Building Materials, v. 467 (March 2025).
- (2024): Quantitative evaluation of sprayability and sag resistance of thin spray-on liners with low CO2 emissions for replacing shotcrete to seal coal mine roadway. In: Case Studies in Construction Materials, v. 21 (December 2024).
- (2024): Influence of silica fume on pore structure, mechanical properties and carbon emission of reactive powder concrete prepared by ice crystal homogenization technology. In: Case Studies in Construction Materials, v. 21 (December 2024).
- (2024): Water resistance, mechanical properties, hydration characteristic and microstructure of magnesium ammonium phosphate cement modified by polyvinyl alcohol powder. In: Construction and Building Materials, v. 440 (August 2024).
- (2024): Enhancement of mechanical properties, durability and service life of low carbon cement paste with super low w/c ratio by incorporating carbon fiber. In: Construction and Building Materials, v. 438 (August 2024).
- (2023): Agglomeration behavior of colloidal nano-silica and its effect on pore structure, mechanical properties and shrinkage of cement mortar. In: Construction and Building Materials, v. 409 (December 2023).
- (2023): Influence of backing layer on the non-metallic encapsulated acoustic emission sensor for concrete monitoring. In: Case Studies in Construction Materials, v. 19 (December 2023).
- (2023): Hydration characteristics, structure evolution of marine cement composites with high durability modified by colloidal nano-silica for low carbon footprints. In: Journal of Building Engineering, v. 75 (September 2023).
- (2023): Investigation on water and fertilizer retention properties of hydrated sulphoaluminate cement pastes modified by bentonite for porous ecological concrete. In: Case Studies in Construction Materials, v. 18 (July 2023).
- (2021): Mix design and rheological properties of magnesium potassium phosphate cement composites based on the 3D printing extrusion system. In: Construction and Building Materials, v. 284 (May 2021).
- (2021): Printability and efflorescence control of admixtures modified 3D printed white Portland cement-based materials based on the response surface methodology. In: Journal of Building Engineering, v. 38 (June 2021).
- (2021): Using layered double hydroxides and anion exchange resin to improve the mechanical properties and chloride binding capacity of cement mortars. In: Construction and Building Materials, v. 272 (February 2021).
- (2020): Effects of modified materials prepared from wastes on the performance of flue gas desulfurization gypsum-based composite wall materials. In: Construction and Building Materials, v. 257 (October 2020).
- (2020): Yield stress and thixotropy control of 3D-printed calcium sulfoaluminate cement composites with metakaolin related to structural build-up. In: Construction and Building Materials, v. 252 (August 2020).
- (2020): Rheological parameters and building time of 3D printing sulphoaluminate cement paste modified by retarder and diatomite. In: Construction and Building Materials, v. 234 (February 2020).
- (2019): Pore structure evolution and strength development of hardened cement paste with super low water-to-cement ratios. In: Construction and Building Materials, v. 227 (December 2019).
- (2019): Recycling of paper sludge powder for achieving sustainable and energy-saving building materials. In: Construction and Building Materials, v. 229 (December 2019).
- (2017): Water absorption and water/fertilizer retention performance of vermiculite modified sulphoaluminate cementitious materials. In: Construction and Building Materials, v. 137 (April 2017).
- (2017): A case of water absorption and water/fertilizer retention performance of super absorbent polymer modified sulphoaluminate cementitious materials. In: Construction and Building Materials, v. 150 (September 2017).
- (2018): Rheological and mechanical properties of admixtures modified 3D printing sulphoaluminate cementitious materials. In: Construction and Building Materials, v. 189 (November 2018).
Structurae cooperates with
