Construction and Building Materials - octobre 2018

Publié:	octobre 2018

Articles dans ce numéro

Auteur(s)	Titre	Page(s)
Huang, Guodong / Ji, Yongsheng / Zhang, Linglei / Li, Jun / Hou, Zhihui	Advances in understanding and analyzing the anti-diffusion behavior in complete carbonation zone of MSWI bottom ash-based alkali-activated concrete	1072-1081
Mohammadinia, Alireza / Arulrajah, Arul / D'Amico, Angelo / Horpibulsuk, Suksun	Alkali-activation of fly ash and cement kiln dust mixtures for stabilization of demolition aggregates	71-78
Zhou, Zilong / Du, Xueming / Wang, Shanyong / Zang, Haizhi	Analysis and engineering application investigation of multiple-hole grouting injections into porous media considering filtration effects	871-883
Zhou, Mi / Lu, Wei / Song, Jianwei / Lee, George C.	Application of Ultra-High Performance Concrete in bridge engineering	1256-1267
Mohseni, Ehsan	Assessment of Na2SiO3 to NaOH ratio impact on the performance of polypropylene fiber-reinforced geopolymer composites	904-911
Nguyen, Dang Mao / Grillet, Anne-Cécile / Bui, Quoc-Bao / Diep, Thi My Hanh / Woloszyn, Monika	Building bio-insulation materials based on bamboo powder and bio-binders	686-698
Ortega, Irene / Pellicer, Teresa M. / Calderón, Pedro A. / Adam, José M.	Cement-based mortar patch repair of RC columns. Comparison with all-four-sides and one-side repair	338-350
Karakurt, Cenk / Çelik, Ahmet Ozan / Yılmazer, Cem / Kiriççi, Volkan / Özyaşar, Ethem	CFD simulations of self-compacting concrete with discrete phase modeling	20-30
Zhang, Dajiang / Zhao, Jihui / Wang, Dongmin / Xu, Chenyang / Zhai, Mengyi / Ma, Xiangdong	Comparative study on the properties of three hydraulic lime mortar systems: Natural hydraulic lime mortar, cement-aerial lime-based mortar and slag-aerial lime-based mortar	42-52
Dorafshan, Sattar / Thomas, Robert J. / Maguire, Marc	Comparison of deep convolutional neural networks and edge detectors for image-based crack detection in concrete	1031-1045
Khabaz, Amjad	Construction and design requirements of green buildings' roofs in Saudi Arabia depending on thermal conductivity principle	1119-1131
Yuan, Huang / Weijian, Yi / Chao, Hu	Corroded reinforced concrete beams under low-speed and low-cycle fatigue loads	644-651
Patterson, Naomi / Yoon, Seyoon / Macphee, Donald E. / Imbabi, Mohammed S.	The cuboid method for measurement of thermal properties of cement-based materials using the guarded heat flow meter	801-810
Wang, Bin / Zhu, Songye	Cyclic tension–compression behavior of superelastic shape memory alloy bars with buckling-restrained devices	103-113
Zhang, Wei / Yao, Xiao / Yang, Tao / Zhang, Zuhua	The degradation mechanisms of alkali-activated fly ash/slag blend cements exposed to sulphuric acid	1177-1187
Khan, Hammad A. / Khan, Mohammad S. H. / Castel, Arnaud / Sunarho, Jerry	Deterioration of alkali-activated mortars exposed to natural aggressive sewer environment	577-597
Do, Tan Manh / Kang, Gyeongo / Vu, Ngan / Kim, Young-Sang	Development of a new cementless binder for marine dredged soil stabilization: Strength behavior, hydraulic resistance capacity, microstructural analysis, and environmental impact	263-275
Shbeeb, Nadim I. / Khasawneh, Mohammad Ali / Al-Omari, Aslam A.	The development of a predictive tool to reduce experimentation time for the polishing and frictional evaluation of asphalt pavement surfaces	740-750
Cao, Shuai / Yilmaz, Erol / Song, Weidong	Dynamic response of cement-tailings matrix composites under SHPB compression load	892-903
Pham, Thong M. / Zhang, X. / Elchalakani, M. / Karrech, A. / Hao, Hong / Ryan, Aarin	Dynamic response of rubberized concrete columns with and without FRP confinement subjected to lateral impact	207-218
Feng, Libang / Yu, Zhengyang / Bian, Yaohui / Wang, Yanping / Zhao, Yanhua / Gou, Liuxiaohui	Effect of failure modes on healing behavior and multiple healing capability of self-healing polyurethanes	1212-1219
Ismail, Mohamed K. / AbdelAleem, Basem H. / Hassan, Assem A. A.	Effect of fiber type on the behavior of cementitious composite beam-column joints under reversed cyclic loading	969-977
Roy, Rahul / Mitra, Ananda / Ganesh, Ajay T. / Sairam, V.	Effect of Graphene Oxide Nanosheets dispersion in cement mortar composites incorporating Metakaolin and Silica Fume	514-524
Yong-Sik, Yoon / Hwa-Sung, Ryu / Hee-Seob, Lim / Kyung-Taek, Koh / Jeong-Su, Kim / Seung-Jun, Kwon	Effect of grout conditions and tendon location on corrosion pattern in PS tendon in grout	1005-1015
Jiang, Chaohua / Jin, Chen / Wang, Yizhi / Yan, Sheng / Chen, Da	Effect of heat curing treatment on the drying shrinkage behavior and microstructure characteristics of mortar incorporating different content ground granulated blast-furnace slag	379-387
Hwang, Chao-Lung / Vo, Duy-Hai / Tran, Vu-An / Yehualaw, Mitiku Damtie	Effect of high MgO content on the performance of alkali-activated fine slag under water and air curing conditions	503-513
Borinaga-Treviño, R. / Orbe, A. / Norambuena-Contreras, J. / Canales, J.	Effect of microwave heating damage on the electrical, thermal and mechanical properties of fibre-reinforced cement mortars	31-41
Zajac, Maciej / Skocek, Jan / Müller, Arnaud / Ben Haha, Mohsen	Effect of sulfate content on the porosity distribution and resulting performance of composite cements	912-919
Liu, Xiguang / Niu, Ditao / Li, Xingchen / Lv, Yao	Effects of Ca(OH)2 – CaCO3 concentration distribution on the pH and pore structure in natural carbonated cover concrete: A case study	1276-1285
Lu, Bao / Shi, Caijun / Zhang, Jiake / Wang, Jiyun	Effects of carbonated hardened cement paste powder on hydration and microstructure of Portland cement	699-708
Wang, Linhao / Li, Xiangyu / Cheng, Yin / Zhang, Yanfei / Bai, Xiaohong	Effects of coal-bearing metakaolin on the compressive strength and permeability of cemented silty soil and mechanisms	174-181
Sun, Chao / Zhu, Yu / Guo, Jian / Zhang, Yamei / Sun, Guoxing	Effects of foaming agent type on the workability, drying shrinkage, frost resistance and pore distribution of foamed concrete	833-839
Carfagnini, Carmela / Baraccani, Simonetta / Silvestri, Stefano / Theodossopoulos, Dimitris	The effects of in-plane shear displacements at the springings of Gothic cross vaults	219-232
Zhang, Junjie / Li, Guoxin / Ye, Wenting / Chang, Yuzhen / Liu, Qingfeng / Song, Zhanping	Effects of ordinary Portland cement on the early properties and hydration of calcium sulfoaluminate cement	1144-1153
Zhang, Chunmei / Li, Yuntao / Cheng, Xiaowei / Liang, Shihan / Guo, Xiaoyang / Zhao, Huijie / Song, Yulong	Effects of plasma-treated rock asphalt on the mechanical properties and microstructure of oil-well cement	163-173
Alhaik, Ghaith / Dubois, Vincent / Wirquin, Eric / Leblanc, Alexandre / Aouad, Georges	Evaluate the influence of starch on earth/hemp or flax straws mixtures properties in presence of superplasticizer	762-772
Siddique, Salman / Shrivastava, Sandeep / Chaudhary, Sandeep	Evaluating resistance of fine bone china ceramic aggregate concrete to sulphate attack	826-832
Murru, A. / Freire-Lista, D. M. / Fort, R. / Varas-Muriel, M. J. / Meloni, P.	Evaluation of post-thermal shock effects in Carrara marble and Santa Caterina di Pittinuri limestone	1200-1211
Guo, Tianxiong / Xie, Yuchen / Weng, Xingzhong	Evaluation of the bond strength of a novel concrete for rapid patch repair of pavements	790-800
Paschalis, Spyridon A. / Lampropoulos, Andreas P. / Tsioulou, Ourania	Experimental and numerical study of the performance of ultra high performance fiber reinforced concrete for the flexural strengthening of full scale reinforced concrete members	351-366
Liang, Chen / Liu, Yuqing / Zhao, Changjun / Lei, Bo / Wu, Jieliang	Experimental and numerical study on an innovative girder-abutment joint in composite bridges with integral abutments	709-730
Perret, Olivier / Lebée, Arthur / Douthe, Cyril / Sab, Karam	Experimental determination of the equivalent-layer shear stiffness of CLT through four-point bending of sandwich beams	1132-1143
Li, Xiang / Zhou, Yuan / Zhang, Xinxing / Zheng, Weixin / Chang, Chenggong / Ren, Xiufeng / Zeng, Jinbo / Hai, Chunxi / Shen, Yue	Experimental investigation of thermal and mechanical properties of magnesium oxychloride cement with form-stable phase change material	670-677
He, Shiqin / Zhu, Zhongfeng / Lv, Miao / Wang, Hui	Experimental study on the creep behaviour of rock-filled concrete and self-compacting concrete	53-61
Chaboki, Hamid Reza / Ghalehnovi, Mansour / Karimipour, Arash / de Brito, Jorge	Experimental study on the flexural behaviour and ductility ratio of steel fibres coarse recycled aggregate concrete beams	400-422
Chu, S. H. / Li, L. G. / Kwan, A. K. H.	Fibre factors governing the fresh and hardened properties of steel FRC	1228-1238
Omran, Ahmed / Soliman, Nancy / Xie, Ailing / Davidenko, Tatyana / Tagnit-Hamou, Arezki	Field trials with concrete incorporating biomass-fly ash	660-669
Cascardi, Alessio / Micelli, Francesco / Aiello, Maria Antonietta	FRCM-confined masonry columns: experimental investigation on the effect of the inorganic matrix properties	811-825
Lee, Cheul-Kyu / Lee, Jae-Young / Lee, Il-Wha / Kim, Yong-Ki	GHG mitigation of railway concrete products using eco-concrete and surface protection agent	1154-1160
Daniele, V. / Taglieri, G. / Macera, L. / Rosatelli, G. / Otero, J. / Charola, A. E.	Green approach for an eco-compatible consolidation of the Agrigento biocalcarenites surface	1188-1199
Xu, Shuqiang / Ma, Qinglin / Wang, Julin / Wang, Lele	Grouting performance improvement for natural hydraulic lime-based grout via incorporating silica fume and silicon-acrylic latex	652-659
Chen, Ru / Gong, Jie / Jiang, Yongjia / Wang, Qingjun / Xi, Zhonghua / Xie, Hongfeng	Halogen-free flame retarded cold-mix epoxy asphalt binders: Rheological, thermal and mechanical characterization	863-870
Agar Ozbek, Ayda Safak / Weerheijm, Jaap / Van Breugel, Klaas	High speed photography technique for measuring impact strength of porous concrete	1092-1104
Qin, Xiantao / Zhu, Siyue / He, Xiang / Jiang, Yi	High temperature properties of high viscosity asphalt based on rheological methods	476-483
Huang, Guodong / Ji, Yongsheng / Zhang, Linglei / Li, Jun / Hou, Zhihui	The influence of curing methods on the strength of MSWI bottom ash-based alkali-activated mortars: The role of leaching of OH− and free alkali	978-985
Azadeh, A. / Ghavami, K.	The influence of heat on shrinkage and water absorption of Dendrocalamus giganteus bamboo as a functionally graded material	145-154
Sajid, Hizb Ullah / Kiran, Ravi	Influence of stress concentration and cooling methods on post-fire mechanical behavior of ASTM A36 steels	920-945
Souza, L. M. S. / Polder, R. B. / Çopuroğlu, O.	The influence of the anolyte solution type and concentration on lithium migration in mortar specimens	123-130
Wang, Xiao-hua / Zhang, She-rong / Wang, Chao / Liu, Fu-cun / Song, Ran / Wei, Pei-yong	Initial damage effect on dynamic compressive behaviors of roller compacted concrete (RCC) under impact loadings	388-399
Cacciotti, Riccardo / Valach, Jaroslav / Wolf, Benjamin	Innovative and easy-to-implement moisture monitoring system for brick units	598-614
Chai, Lijuan / Guo, Liping / Chen, Bo / Xu, Yanhui	Interactive effects of freeze-thaw cycle and carbonation on tensile property of ecological high ductility cementitious composites for bridge deck link slab	773-781
Chen, Changfu / Zhang, Genbao / Zornberg, Jorge G. / Morsy, Amr M. / Zhu, Shimin / Zhao, Hongbo	Interface behavior of tensioned bars embedded in cement-soil mixtures	840-853
Abdulmatin, Akkadath / Tangchirapat, Weerachart / Jaturapitakkul, Chai	An investigation of bottom ash as a pozzolanic material	155-162
Can, Ömer	Investigation of seismic performance of in-plane aligned masonry panels strengthened with Carbon Fiber Reinforced Polymer	854-862
Lu, Wei / Wang, Yu / Chen, Haodong / Jiang, Lin / Duan, Qiangling / Li, Mi / Wang, Qingsong / Sun, Jinhua	Investigation of the thermal response and breakage mechanism of point-supported glass facade under wind load	635-643
Sudarsanan, Nithin / Karpurapu, Rajagopal / Amrithalingam, Veeraragavan	An investigation on the interface bond strength of geosynthetic-reinforced asphalt concrete using Leutner shear test	423-437
Che, Tiankai / Pan, Baofeng / Ouyang, Jian	The laboratory evaluation of incorporating ceramsite into HMA as fine aggregates	1239-1246
Jing, Guoqing / Fu, Hao / Aela, Peyman	Lateral displacement of different types of steel sleepers on ballasted track	1268-1275
Yilmaz, Tolga / Kirac, Nevzat / Anil, Özgür / Erdem, R. Tuğrul / Sezer, Ceyda	Low-velocity impact behaviour of two way RC slab strengthening with CFRP strips	1046-1063
Noushini, Amin / Hastings, Max / Castel, Arnaud / Aslani, Farhad	Mechanical and flexural performance of synthetic fibre reinforced geopolymer concrete	454-475
Navarro, R. / Alcocel, E. G. / Sánchez, I. / Garcés, P. / Zornoza, E.	Mechanical properties of alkali activated ground SiMn slag mortars with different types of aggregates	79-89
Askarian, Mahya / Tao, Zhong / Adam, Georgius / Samali, Bijan	Mechanical properties of ambient cured one-part hybrid OPC-geopolymer concrete	330-337
Sengul, Ozkan	Mechanical properties of slurry infiltrated fiber concrete produced with waste steel fibers	1082-1091
Punurai, Wonsiri / Kroehong, Wunchock / Saptamongkol, Adam / Chindaprasirt, Prinya	Mechanical properties, microstructure and drying shrinkage of hybrid fly ash-basalt fiber geopolymer paste	62-70
Zhang, Jinpeng / Liu, Limin / Cao, Junzhi / Yan, Xu / Zhang, Futao	Mechanism and application of concrete-filled steel tubular support in deep and high stress roadway	233-246
Dvorkin, L. / Zhitkovsky, V. / Stepasyuk, Y. / Ribakov, Y.	A method for design of high strength concrete composition considering curing temperature and duration	731-739
Wu, Jianmin / Li, Dawei / Zhu, Baihe / Wu, Chunsheng	Milling process simulation of old asphalt mixture by discrete element	996-1004
Cui, Peide / Xiao, Yue / Yan, Boxiang / Li, Mingliang / Wu, Shaopeng	Morphological characteristics of aggregates and their influence on the performance of asphalt mixture	303-312
Robira, M. / Hilloulin, B. / Loukili, A. / Potin, G. / Bourbon, X. / Abdelouas, A.	Multi-scale investigation of the effect of γ irradiations on the mechanical properties of cementitious materials	484-494
Wang, Yanlei / Zhang, Xue / Cai, Gaochuang / Wan, Baolin / Waldmann, Danièle / Qu, Yuan	A new thickness-based accelerated aging test methodology for resin materials: Theory and preliminary experimental study	986-995
Yang, Yonggan / Zhang, Yunsheng / She, Wei / Wu, Zhitao / Liu, Zhiyong / Ding, Yajiu	Nondestructive monitoring the deterioration process of cement paste exposed to sodium sulfate solution by X-ray computed tomography	182-190
Kim, Gun / Park, Sangyun / Kim, Jin-Yeon / Kurtis, Kimberly E. / Hayes, Nolan W. / Jacobs, Laurence J.	Nonlinear Rayleigh surface waves to characterize microscale damage due to alkali-silica reaction (ASR) in full-scale, nuclear concrete specimens	1114-1118
Zhang, Weipeng / Yao, Xu / Khanal, Santosh / Xu, Shiai	A novel surface treatment for bamboo flour and its effect on the dimensional stability and mechanical properties of high density polyethylene/bamboo flour composites	1220-1227
Hunashikatti, Ganesh M. / Pradhan, Subhasis / Barai, Sudhirkumar V.	Partially hydrated recycled aggregate concrete: A systematic approach towards sustainable development	537-549
Saadoon, Tahseen / Gómez-Meijide, Breixo / García, Álvaro	Prediction of water evaporation and stability of cold asphalt mixtures containing different types of cement	751-761
Alghamri, R. / Kanellopoulos, A. / Litina, C. / Al-Tabbaa, A.	Preparation and polymeric encapsulation of powder mineral pellets for self-healing cement based materials	247-262
Motahari Karein, S. Mahmoud / Vosoughi, Payam / Isapour, Soroush / Karakouzian, Moses	Pretreatment of natural perlite powder by further milling to use as a supplementary cementitious material	782-789
Algin, Zeynep / Ozen, Mustafa	The properties of chopped basalt fibre reinforced self-compacting concrete	678-685
Sappakittipakorn, Manote / Sukontasukkul, Piti / Higashiyama, Hiroshi / Chindaprasirt, Prinya	Properties of hooked end steel fiber reinforced acrylic modified concrete	1247-1255
Ismail, N. / El-Maaddawy, T. / Khattak, N.	Quasi-static in-plane testing of FRCM strengthened non-ductile reinforced concrete frames with masonry infills	1286-1298
Lee, Dongkyu / Shin, Soomi / Doan, Quoc Hoan	Real-time robust assessment of angles and positions of nonscaled steel outrigger structure with Maxwell-Mohr method	1161-1176
Duan, Siyu / Liao, Hongqiang / Ma, Zhibin / Cheng, Fangqin / Fang, Li / Gao, Hongyu / Yang, Hengquan	The relevance of ultrafine fly ash properties and mechanical properties in its fly ash-cement gelation blocks via static pressure forming	1064-1071
Osio-Norgaard, Jorge / Gevaudan, Juan Pablo / Srubar, Wil V.	A review of chloride transport in alkali-activated cement paste, mortar, and concrete	191-206
Bagheri, Mohammadreza / Shariatipour, Seyed M. / Ganjian, Eshmaiel	A review of oil well cement alteration in CO2-rich environments	946-968
Ebrahimi, Khashayar / Daiezadeh, Mohammad Javad / Zakertabrizi, Mohammad / Zahmatkesh, Farhad / Habibnejad korayem, Asghar	A review of the impact of micro- and nanoparticles on freeze-thaw durability of hardened concrete: Mechanism perspective	1105-1113
Ng, Connie / Alengaram, U. Johnson / Wong, Leong Sing / Mo, Kim Hung / Jumaat, Mohd Zamin / Ramesh, S.	A review on microstructural study and compressive strength of geopolymer mortar, paste and concrete	550-576
Kakade, Vijay B. / Reddy, M. Amaranatha / Reddy, K. Sudhakar	Rutting performance of hydrated lime modified bituminous mixes	1-10
Niu, Lihua / Zheng, Shansuo / Zheng, Hao / Zhou, Yan / Pei, Pei	Seismic behavior of confined masonry walls subjected to freeze-thaw cycles	131-144
Mazumder, Mithil / Ahmed, Raju / Wajahat Ali, Ahmed / Lee, Soon-Jae	SEM and ESEM techniques used for analysis of asphalt binder and mixture: A state of the art review	313-329
Li, Dawang / Xiong, Cheng / Huang, Tong / Wei, Ren / Han, Ningxu / Xing, Feng	A simplified constitutive model for corroded steel bars	11-19
Perez, G. / Allegro, V. R. / Corroto, M. / Pons, A. / Guerrero, A.	Smart reversible thermochromic mortar for improvement of energy efficiency in buildings	884-891
Wang, Yanlei / Wang, Yongshuai / Han, Baoguo / Wan, Baolin / Cai, Gaochuang / Li, Zhizheng	Strain monitoring of concrete components using embedded carbon nanofibers/epoxy sensors	367-378
Djafar-Henni, Imane / Kassoul, Amar	Stress–strain model of confined concrete with Aramid FRP wraps	1016-1030
Ma, Chau-Khun / Awang, Abdullah Zawawi / Omar, Wahid	Structural and material performance of geopolymer concrete: A review	90-102
Sun, Zengqing / Lin, Xiaochen / Liu, Pengfei / Wang, Dawei / Vollpracht, Anya / Oeser, Markus	Study of alkali activated slag as alternative pavement binder	626-634
Lahouar, Mohamed Amine / Caron, Jean-François / Foret, Gilles / Benzarti, Karim / Mege, Romain	Temperature effect on the mechanical behavior of glued-in rods intended for the connection of timber elements	438-453
Savino, V. / Lanzoni, L. / Tarantino, A. M. / Viviani, M.	Tensile constitutive behavior of high and ultra-high performance fibre-reinforced-concretes	525-536
Pachón-Montaño, A. / Sánchez-Montero, J. / Andrade, C. / Fullea, J. / Moreno, E. / Matres, V.	Threshold concentration of chlorides in concrete for stainless steel reinforcement: Classic austenitic and new duplex stainless steel	495-502
Hu, Yong / Li, Yun An / Ruan, Cheng Ke / Lin, Jun Lin / Chen, Shu Jian / Tang, Hui Ming / Duan, Wen Hui	Transformation of pore structure in consolidated silty clay: New insights from quantitative pore profile analysis	615-625
He, Zhen / Hu, Lingling / Li, Yang / Hu, Jun / Shao, Yixin	Use of sandstone powder as a mineral additive for concrete	276-286
Jiapei, Du / Yuhuan, Bu / Xuechao, Cao / Zhonghou, Shen / Baojiang, Sun	Utilization of alkali-activated slag based composite in deepwater oil well cementing	114-122
Shanbara, Hayder Kamil / Ruddock, Felicite / Atherton, William	A viscoplastic model for permanent deformation prediction of reinforced cold mix asphalt	287-302

Informations
sur cette fiche
IssueID
21509
Publié(e) le:
25.11.2018
Modifié(e) le:
30.06.2019

Publicité

Structurae coopère avec

International Association for Bridge and Structural Engineering (IABSE)

Publicité

Construction and Building Materials - octobre 2018

Articles dans ce numéro

Vous avez dépassé votre limite de téléchargement mensuelle !

Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois.
Les utilisateurs·rices de Structurae Pro sont limités à 50.

Données obligatoires

Construction and Building Materials - octobre 2018

Articles dans ce numéro

Vous avez dépassé votre limite de téléchargement mensuelle ! Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois. Les utilisateurs·rices de Structurae Pro sont limités à 50.

Données obligatoires

Vous avez dépassé votre limite de téléchargement mensuelle !

Les abonné·es à Structurae Plus peuvent télécharger 30 images ou ensembles de données par mois.
Les utilisateurs·rices de Structurae Pro sont limités à 50.