René Steiger 
- (2024): Shear resistance of Oriented Strand Board panel sheathings in timber-framed shear walls. In: Engineering Structures, v. 316 (Oktober 2024).
- (2024): Steel-Reinforced Columns Made of European Beech Glued-Laminated Timber. In: Journal of Structural Engineering (ASCE), v. 150, n. 2 (Februar 2024).
- (2021): Brettschichtholz aus Buche. In: Bautechnik, v. 98 (November 2021).
- (2015): Les efforts horizontaux dans le dimensionnement des bâtiments en bois. In: Tracés, v. 141, n. 11 (5 Juni 2015).
- (2003): Norm SIA 265 : Holzbau. In: TEC21, v. 129, n. 29-30 (22 Juli 2003).
- (2013): Geklebt, nicht gedreht. In: TEC21, v. 139, n. 23 (31 Mai 2013).
- (1997): Tragverhalten von Fichten-Kanthölzern bei M/N-Interaktion. In: Schweizer Ingenieur und Architekt, v. 115, n. 30-31 (28 Juli 1997).
- (2021): Experimental investigation of OSB sheathed timber frame shear walls with strong anchorage subjected to cyclic lateral loading. In: Engineering Structures, v. 226 (Januar 2021).
- (2020): Glulam columns made of European beech timber: compressive strength and stiffness parallel to the grain, buckling resistance and adaptation of the effective-length method according to Eurocode 5. In: Materials and Structures, v. 53, n. 4 (26 Juni 2020).
- (2020): Structural health monitoring of timber structures – Review of available methods and case studies. In: Construction and Building Materials, v. 248 (Juli 2020).
- (2013): Failures in Large-Span Roof Structures in Switzerland. Vorgetragen bei: IABSE Workshop: Safety, Failures and Robustness of Large Structures, Helsinki, Finland, 14-15 February 2013.
- (2015): Strengthening of timber structures with glued-in rods. In: Construction and Building Materials, v. 97 (Oktober 2015).
- (2018): Experimental investigation of friction stresses between adjacent panels made of Oriented Strand Board (OSB) and between OSB panels and glued laminated timber (GLT) frame members. In: Materials and Structures, v. 51, n. 1 (Februar 2018).
- (2017): Analysis of shear transfer and gap opening in timber–concrete composite members with notched connections. In: Materials and Structures, v. 50, n. 5 (Oktober 2017).
- (2011): State-of-the-art review on timber connections with glued-in steel rods. In: Materials and Structures, v. 44, n. 5 (Juni 2011).
- (2013): Strain-based calculation model for centrically and eccentrically loaded timber columns. In: Engineering Structures, v. 56 (November 2013).
- (2010): Influence of asphalt pavement on damping ratio and resonance frequencies of timber bridges. In: Engineering Structures, v. 32, n. 10 (Oktober 2010).
- (2017): Bending tests on timber-concrete composite members made of beech laminated veneer lumber with notched connection. In: Engineering Structures, v. 132 (Februar 2017).
- (2014): State-of-the-Art Review of Approaches for the Design of Timber Beams with Notches. In: Journal of Structural Engineering (ASCE), v. 140, n. 3 (März 2014).
- (2015): Experimental modal analysis of a multi-storey light-frame timber building. In: Bulletin of Earthquake Engineering, v. 15, n. 8 (September 2015).
- (2017): Calculation model to assess the structural behavior of LVL-concrete composite members with ductile notched connection. In: Engineering Structures, v. 153 (Dezember 2017).
- (2018): OSB sheathed light-frame timber shear walls with strong anchorage subjected to vertical load, bending moment, and monotonic lateral load. In: Engineering Structures, v. 173 (Oktober 2018).
- (2007): Cross-Laminated Timber Plates: Evaluation and Verification of Homogenized Elastic Properties. In: Journal of Structural Engineering (ASCE), v. 133, n. 1 (Januar 2007).
Structurae kooperiert mit
