Sébastien Remond 
- (2023): Effects of Crushing and Grinding on the Porosity of Hardened Cement Paste. In: Buildings, v. 13, n. 9 (23 August 2023).
- (2023): A methodology for designing 3D printable mortar based on recycled sand. In: Materials and Structures, v. 56, n. 9 (11 Oktober 2023).
- (2023): Probabilistic prediction of structural failure during 3D concrete printing processes. In: Materials and Structures, v. 56, n. 4 (13 April 2023).
- (2014): A DEM hard-core soft-shell model for the simulation of concrete flow. In: Cement and Concrete Research, v. 58 (April 2014).
- (2011): Influence of cement grouts composition on the rheological behaviour. In: Cement and Concrete Research, v. 41, n. 3 (März 2011).
- (2010): High temperature behaviour of self-consolidating concrete. In: Cement and Concrete Research, v. 40, n. 3 (März 2010).
- (2009): Self-consolidating concrete subjected to high temperature. In: Cement and Concrete Research, v. 39, n. 12 (Dezember 2009).
- (2023): Portland/Sulfoaluminate Cement Blends for the Control of Early Age Hydration and Yield Stress. In: Buildings, v. 13, n. 2 (14 Februar 2023).
- (2021): Durability assessment and microstructural analysis of 3D printed concrete exposed to sulfuric acid environments. In: Construction and Building Materials, v. 290 (Juli 2021).
- (2021): Intra granular porosity of mineral powders: modeling and experimentation. In: Materials and Structures, v. 54, n. 2 (23 Februar 2021).
- (2021): Alternative hydraulic binder development based on brick fines: Influence of particle size and substitution rate. In: Journal of Building Engineering, v. 39 (Juli 2021).
- (2020): Inter-layer reinforcement of 3D printed concrete elements. In: Asian Journal of Civil Engineering, v. 22, n. 2 (Oktober 2020).
- (2022): Influence of the mix composition on the thixotropy of 3D printable mortars. In: Magazine of Concrete Research, v. 74, n. 6 (März 2022).
- (2020): Mechanical assessment of concrete – Steel bonding in 3D printed elements. In: Construction and Building Materials, v. 256 (September 2020).
- (2020): Numerical investigation of parameters influencing fire evaluation tests of chemically bonded anchors in uncracked concrete. In: Engineering Structures, v. 209 (April 2020).
- (2020): Homogenization process of field samples of recycled aggregates. In: Construction and Building Materials, v. 243 (Mai 2020).
- (2018): Heterogeneity of recycled concrete aggregates, an intrinsic variability. In: Construction and Building Materials, v. 175 (Juni 2018).
- (2018): Quantitative assessment of the saturation degree of model fine recycled concrete aggregates immersed in a filler or cement paste. In: Construction and Building Materials, v. 175 (Juni 2018).
- (2020): Effect of the printing method and mortar’s workability on pull-out strength of 3D printed elements. In: Construction and Building Materials, v. 230 (Januar 2020).
- (2019): Influence of testing conditions on thermal distribution and resulting load-bearing capacity of bonded anchors under fire. In: Engineering Structures, v. 192 (August 2019).
- (2003): Comportement au feu des bétons. In: Revue française de Génie civil, v. 7, n. 10 (Dezember 2003).
- (2003): Comportement au feu des bétons. In: Revue française de Génie civil, v. 7, n. 1 (Januar 2003).
- (2015): Influence of fine recycled concrete aggregates on the properties of mortars. In: Construction and Building Materials, v. 81 (April 2015).
- (2016): Fresh behavior of mortar based on recycled sand – Influence of moisture condition. In: Construction and Building Materials, v. 106 (März 2016).
- (2017): Hardened behavior of mortar based on recycled aggregate: Influence of saturation state at macro- and microscopic scales. In: Construction and Building Materials, v. 141 (Juni 2017).
- (2017): Use of calcium sulfoaluminate cements for setting control of 3D-printing mortars. In: Construction and Building Materials, v. 157 (Dezember 2017).
- (2017): Impact of the initial moisture level and pre-wetting history of recycled concrete aggregates on their water absorption. In: Materials and Structures, v. 50, n. 5 (Oktober 2017).
- (2010): Bétons autoplaçants à haute température. Propriétés mécaniques et physico-chimiques. In: European Journal of Environmental and Civil Engineering, v. 14, n. 1 (Januar 2010).
- (2018): Improving the properties of recycled concrete aggregates by accelerated carbonation. In: Proceedings of the Institution of Civil Engineers - Construction Materials, v. 171, n. 3 (Juni 2018).
- (2011): Microstructure et propriétés physico-chimiques de bétons autoplaçants chauffés de 20 à 600°C. In: European Journal of Environmental and Civil Engineering, v. 15, n. 6 (Juli 2011).
Structurae kooperiert mit
